Home › Engine / Hybrid System › A25A-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.08
RM3620E _51 Engine / Hybrid System _076487 A25A-FKS STARTING _0372221 STARTER(w/ Stop And Start System) A

A25A-FKS STARTING  STARTER(w/ Stop And Start System)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE WIRE HARNESS

a.
A470734C01
0.25,0.906 0.458,0.906 false 0.24,0.313 0.354,0.313 false 0.688,0.896 0.844,0.896 false 0.094,0.823 0.406,0.979 0.313,0.156 10 false *1 0.094,0.208 0.406,0.365 0.313,0.156 10 false *a 0.885,0.802 1.125,1.01 0.24,0.208 10 false *b
*1 Wire Harness
*a Nut
*b Noise Filter Harness


Remove the 2 nuts and wire harness from the starter assembly.


b.

Disconnect the noise filter harness from the repair service starter kit.


Hide 28249 2.REMOVE STARTER INRUSH CURRENT REDUCTION RELAY

a.
A470735C01
0.385,1.156 0.521,1.156 0.521,1.156 0.979,1.677 true 0.219,1.073 0.385,1.229 0.167,0.156 10 false *a
*a Lead Wire


Remove the nut and disconnect the lead wire from terminal M.


b.

Remove the 2 bolts and starter inrush current reduction relay from the starter drive housing assembly.


Hide 28226B 3.REMOVE REPAIR SERVICE STARTER KIT

a.
A470736

While holding the repair service starter kit to the starter drive housing assembly, remove the 2 nuts.


b.
A414106C01
0.333,1.823 0.521,1.823 0.521,1.823 0.844,0.625 true 1.635,0.385 1.76,0.156 1.76,0.156 1.896,0.156 false 1.885,0.427 2.135,0.302 2.135,0.302 2.271,0.302 false 0.177,1.729 0.49,1.885 0.313,0.156 10 false *1 2.292,0.219 2.604,0.375 0.313,0.156 10 false *2 1.917,0.063 2.229,0.219 0.313,0.156 10 false *a
*1 Pinion Drive Lever
*2 Plunger
*a Hook


While lifting the rear of the magnet switch, remove the hook from the pinion drive lever, and then remove the repair service starter kit.

NOTICE:

Do not drop the plunger when removing the repair service starter kit.



Hide 28120 4.REMOVE STARTER YOKE ASSEMBLY

a.
A414107C01
0.896,1.969 1.115,1.969 1.115,1.969 1.646,1.771 false 3.052,2.021 2.927,2.021 2.927,2.021 2.677,1.865 false 0.729,1.885 1.042,2.042 0.313,0.156 10 false *1 3.073,1.938 3.385,2.094 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, remove the 2 through bolts, and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 5.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A414108C01
2.667,0.302 2.99,0.302 false 0.677,1.875 0.896,1.875 0.896,1.875 1.323,1.635 false 2.646,1.813 2.969,1.813 false 3.01,0.219 3.323,0.375 0.313,0.156 10 false *a 0.531,1.792 0.844,1.948 0.313,0.156 10 false *1 2.99,1.74 3.302,1.896 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly
*a Lead Wire


Remove the 2 screws.


b.

While holding down the lead wire, remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 28140 6.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C06
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Brush Spring
*b Brush


Using a screwdriver, hold the brush spring back and disconnect the 4 brushes.


b.

Remove the starter brush holder assembly from the starter armature assembly.


Hide 28160 7.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438C06
1.49,0.406 1.938,0.229 1.938,0.229 2.188,0.229 false 1.615,1.958 1.823,1.958 1.823,1.958 2.073,1.635 false 2.229,0.135 2.542,0.333 0.313,0.198 10 false *1 1.448,1.875 1.76,2.073 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 8.REMOVE STARTER ARMATURE PLATE

a.
A414109C01
0.573,0.375 0.938,0.375 false 2.365,0.885 2.521,0.333 2.521,0.333 2.74,0.333 false 0.865,1.979 1.094,1.979 1.094,1.979 1.354,1.719 false 1.719,1.99 1.917,1.99 1.917,1.99 2.25,1.646 true 2.771,0.24 3.083,0.396 0.313,0.156 10 false *1 0.417,0.281 0.729,0.438 0.313,0.156 10 false *2 0.698,1.885 1.01,2.042 0.313,0.156 10 false *3 1.563,1.896 1.875,2.052 0.313,0.156 10 false *3
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*3 Starter Armature Plate


Remove the starter armature plate from the starter drive housing assembly or starter yoke assembly.


Hide 9.REMOVE PLANETARY GEAR

a.
A414110

Remove the 3 planetary gears from the starter center bearing clutch sub-assembly.


Hide 28021 10.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A414111C01
2,0.292 2.333,0.292 false 2.802,0.75 2.948,0.333 2.948,0.333 3.094,0.333 false 2.615,1.698 2.948,1.698 false 2.979,1.615 3.292,1.771 0.313,0.156 10 false *1 2.365,0.208 2.677,0.365 0.313,0.156 10 false *2 3.115,0.25 3.427,0.406 0.313,0.156 10 false *3
*1 Starter Center Bearing Clutch Sub-assembly
*2 Pinion Drive Lever
*3 Rubber Seal


Remove the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal from the starter drive housing assembly.


b.

Remove the pinion drive lever and rubber seal from the starter center bearing clutch sub-assembly.