Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System) › from 2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B166D  Lost Communication with Front Door Pressure Sensor RH  B166E  Front Door Pressure Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit consists of the airbag sensor assembly and side airbag pressure sensor RH.

The side airbag pressure sensor RH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the circuit for the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B166D Lost Communication with Front Door Pressure Sensor RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A side airbag pressure sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag pressure sensor RH

·

Airbag sensor assembly


Comes on Not applicable
B166E Front Door Pressure Sensor RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A side airbag pressure sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag pressure sensor RH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

E444927E02
5.344,1.958 5.802,2.156 0.458,0.198 10 false M15 5.333,2.135 7.042,2.354 1.708,0.219 10 false Airbag Sensor Assembly 5.552,0.75 6.01,0.948 0.458,0.198 10 false BBR+ 5.552,1.375 6.01,1.573 0.458,0.198 10 false BBR- 5.271,0.646 5.552,0.844 0.281,0.198 10 false 25 5.271,1.25 5.552,1.448 0.281,0.198 10 false 26 3.458,0.771 3.74,0.969 0.281,0.198 10 false IM2 3.469,1.385 3.75,1.583 0.281,0.198 10 false IM2 3.51,0.573 3.792,0.771 0.281,0.198 10 false 1 3.521,1.177 3.802,1.375 0.281,0.198 10 false 2 3.417,0.979 3.875,1.177 0.458,0.198 10 false BDR+ 3.427,1.594 3.885,1.792 0.458,0.198 10 false BDR- 1.625,0.635 1.906,0.833 0.281,0.198 10 false 2 1.625,1.25 1.906,1.448 0.281,0.198 10 false 1 1.146,0.771 1.604,0.969 0.458,0.198 10 false BDR+ 1.135,1.406 1.594,1.604 0.458,0.198 10 false BDR- 0.125,1.781 0.583,1.979 0.458,0.198 10 false I10 0.115,1.958 2.333,2.25 2.219,0.292 10 false Side Airbag Pressure Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag pressure sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
E444929C01
0.396,1.573 0.708,1.729 0.313,0.156 10 false *1 2.583,1.5 2.896,1.656 0.313,0.156 10 false *2 1.125,1.385 1.438,1.542 0.313,0.156 10 false *3 1.656,1.406 1.969,1.563 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the connectors from the airbag sensor assembly and side airbag pressure sensor RH.


b.

Check that the connectors (on the airbag sensor assembly side and side airbag pressure sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE RH OR FLOOR WIRE

3.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT
a.
E449098C01
1.135,3.531 1.552,3.781 0.417,0.25 0.865,0.573 1.281,0.823 0.417,0.25 1.365,1.135 1.5,1.135 1.5,1.135 1.677,0.688 true 2.188,1.135 2.063,1.135 2.063,1.135 1.927,0.688 true 2.698,3.354 2.563,3.354 2.563,3.354 1.875,3.917 true 2.042,4.406 1.906,4.406 1.906,4.406 1.833,4.219 true 2.375,2.927 2.24,2.927 2.24,2.927 1.792,3.927 true 0.729,2.167 0.875,2.354 0.146,0.188 10 false F 0.417,2.646 0.625,2.833 0.208,0.188 10 false *1 0.979,2.167 1.115,2.354 0.135,0.188 10 false E 2.031,2.167 2.167,2.354 0.135,0.188 10 false B 1.156,1.958 1.365,2.146 0.208,0.188 10 false *3 1.74,1.958 1.948,2.146 0.208,0.188 10 false *4 2.302,2.177 2.438,2.365 0.135,0.188 10 false A 2.677,2.438 2.885,2.625 0.208,0.188 10 false *2 1,0.625 1.26,0.813 0.26,0.188 10 false I10 0.677,0.146 0.885,0.333 0.208,0.188 10 false *a 0.969,1.073 1.49,1.24 0.521,0.167 10 false BDR- 2.25,1.052 2.813,1.219 0.563,0.167 10 false BDR+ 1.219,3.583 1.594,3.75 0.375,0.167 10 false M15 0.948,2.885 1.156,3.073 0.208,0.188 10 false *b 2.125,4.302 2.344,4.448 0.219,0.146 10 false *5 1.427,2.167 1.563,2.333 0.135,0.167 10 false D 1.583,2.167 1.719,2.333 0.135,0.167 10 false C 2.438,2.854 3,3.021 0.563,0.167 10 false BBR+ 2.76,3.281 3.281,3.448 0.521,0.167 10 false BBR-
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I10-2 (BDR+) - Body ground Power switch on (IG) Below 1 V
I10-1 (BDR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always 1 MΩ or higher
I10-2 (BDR+) - Body ground Always 1 MΩ or higher
I10-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SIDE AIRBAG PRESSURE SENSOR RH

NG

5.CHECK CONNECTORS
4.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.
E444928C01
0.719,1.531 1.51,2.167 0.792,0.635 10 false *1 2.573,1.51 2.927,1.917 0.354,0.406 10 false *2
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag pressure sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B166D or B166E is output
DTC B167B or B167C is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors to them.



DTC B166D or B166E is output

DTC B167B or B167C is output

DTCs B166D, B166E, B167B and B167C are not output

5.CHECK CONNECTORS
a.
E444930C01
0.427,1.635 0.74,1.792 0.313,0.156 10 false *1 2.625,1.49 2.938,1.646 0.313,0.156 10 false *2 1.104,1.396 1.417,1.552 0.313,0.156 10 false *3 1.719,1.406 2.031,1.563 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire RH.


b.

Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

6.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

6.CHECK FLOOR WIRE
a.
E449099C01
1.083,3.583 1.5,3.833 0.417,0.25 1.042,0.635 1.458,0.885 0.417,0.25 1.333,0.25 1.5,0.25 1.5,0.25 1.719,0.531 true 2.167,0.25 2,0.25 2,0.25 1.875,0.552 true 2.073,4.448 1.906,4.448 1.906,4.448 1.833,4.219 true 2.333,2.99 2.167,2.99 2.167,2.99 1.813,3.906 true 2.729,3.208 2.563,3.208 2.563,3.208 1.885,3.927 true 0.99,0.198 1.677,0.406 0.688,0.208 10 false BDR- 2.229,0.177 2.656,0.573 0.427,0.396 10 false BDR+ 2.292,2.198 2.479,2.427 0.188,0.229 10 false A 2.073,2.188 2.26,2.417 0.188,0.229 10 false B 1.604,2.177 1.792,2.406 0.188,0.229 10 false C 1.396,2.177 1.583,2.406 0.188,0.229 10 false D 0.958,2.188 1.177,2.448 0.219,0.26 10 false E 0.729,2.198 0.948,2.458 0.219,0.26 10 false F 2.625,2.469 2.885,2.698 0.26,0.229 10 false *2 0.406,2.677 0.667,2.906 0.26,0.229 10 false *1 1.167,0.677 1.5,0.854 0.333,0.177 10 false IM2 0.646,0.167 0.906,0.396 0.26,0.229 10 false *a 0.927,2.885 1.188,3.115 0.26,0.229 10 false *b 1.125,1.958 1.385,2.188 0.26,0.229 10 false *3 1.729,1.948 1.99,2.177 0.26,0.229 10 false *4 1.177,3.635 1.5,3.813 0.323,0.177 10 false M15 2.396,2.917 3.083,3.125 0.688,0.208 10 false BBR+ 2.792,3.125 3.365,3.333 0.573,0.208 10 false BBR- 2.125,4.354 2.385,4.583 0.26,0.229 10 false *5
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM2-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
IM2-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always 1 MΩ or higher
IM2-1 (BDR+) - Body ground Always 1 MΩ or higher
IM2-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE