Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › EGR VALVE › from 2020.08
RM3620E _51 Engine / Hybrid System _076502 A25A-FKS EMISSION CONTROL _0372396 EGR VALVE A

A25A-FKS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 25680 4.REMOVE EGR COOLER ASSEMBLY

Hide 5.DISCONNECT ENGINE WIRE

a.
A402225C01
0.875,0.042 1.083,0.24 0.208,0.198 10 true *a 2.844,0.323 3.063,0.521 0.219,0.198 10 true *b
*a No. 5 Engine Wire Connector
*b EGR Valve Assembly Connector


Disconnect the No. 5 engine wire connector.


b.

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25601 6.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A402228

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A402226

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 7.REMOVE EGR VALVE ASSEMBLY

a.
A402229

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.
A430162

Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.


c.
A402232

Remove the 2 bolts and EGR cooler bracket from the EGR valve bracket and water outlet.


d.
A473006

Using an 8 mm socket wrench, remove the bolt.


e.
A473007C02
2.281,1 2.625,0.74 2.625,0.74 2.771,0.74 true 2.281,1.094 2.49,1.094 true 2.552,1 2.865,1.198 0.313,0.198 10 true *a 2.823,0.646 3.135,0.844 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket from the camshaft housing vertically.


f.
A402235

Using an 8 mm socket wrench, remove the bolt and EGR valve assembly from the EGR valve bracket.