Home › Engine / Hybrid System › A25B-FXS (EMISSION CONTROL) › EGR VALVE › from 2020.08
RM3620E _51 Engine / Hybrid System _080119 A25B-FXS EMISSION CONTROL _0389277 EGR VALVE A

A25B-FXS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT (for Engine)

Hide 2.DISCONNECT ENGINE WIRE

a.
A405761C01
1.531,1.302 1.729,0.885 1.729,0.885 1.948,0.885 true 0.99,1.969 1.24,1.969 1.24,1.969 1.406,1.552 true 1.969,0.802 2.208,0.979 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Disengage the 3 hose clamps and disconnect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


b.
A441031

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25680 3.DISCONNECT EGR COOLER ASSEMBLY

a.
A441035

Remove the 2 bolts and disconnect the EGR cooler assembly from the EGR valve assembly.


b.

Remove the EGR valve gasket from the EGR valve assembly.


Hide 25601 4.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A441032

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A402226

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 5.REMOVE EGR VALVE ASSEMBLY

a.
A441033

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.
A441034

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR valve assembly.


c.
A469689

Using an 8 mm socket wrench, remove the bolt.


d.
A469690C02
2.5,1.25 2.333,1.25 2.333,1.25 2.125,0.865 true 2.583,0.583 2.417,0.583 2.417,0.583 2.104,0.781 true 2.583,0.5 2.833,0.667 0.25,0.167 10 true *b 2.5,1.167 2.75,1.333 0.25,0.167 10 true *a
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket from the camshaft housing vertically.


e.
A441039

Using an 8 mm socket wrench, remove the bolt and EGR valve assembly from the EGR valve bracket.