Home › Engine / Hybrid System › A25B-FXS (EMISSION CONTROL) › EGR VALVE › from 2020.08
RM3620E _51 Engine / Hybrid System _080119 A25B-FXS EMISSION CONTROL _0389277 EGR VALVE A

A25B-FXS EMISSION CONTROL  EGR VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 25620 1.INSTALL EGR VALVE ASSEMBLY

a.

Using an 8 mm socket wrench, install the EGR valve assembly to the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A469691C02
2.125,0.771 2.583,0.417 2.583,0.417 2.75,0.417 true 2.115,0.865 2.417,1.25 2.417,1.25 2.583,1.25 true 2.583,1.167 2.833,1.333 0.25,0.167 10 true *a 2.75,0.333 3,0.5 0.25,0.167 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing.


c.

Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 4 water by-pass hose to the EGR valve assembly, and slide the clip to secure the hose.


e.

Connect the No. 8 water by-pass hose to the EGR valve assembly, and slide the clip to secure the hose.


Hide 25601 2.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Install a new EGR inlet gasket to the intake manifold.


b.

Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.


c.

Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25680 3.CONNECT EGR COOLER ASSEMBLY

a.
A441040C01
1.667,1.125 1.771,0.719 1.771,0.719 1.906,0.719 true 1.135,1.656 1.031,1.521 1.031,1.521 0.865,1.521 true 1.365,1.792 1.875,1.896 1.875,1.896 1.729,1.365 true 0.604,1.385 0.813,1.583 0.208,0.198 10 true *a 1.948,0.583 2.156,0.781 0.208,0.198 10 true *a 1.938,1.833 2.146,2.031 0.208,0.198 10 true *a
*a Claw


Install a new EGR valve gasket to the EGR valve assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.



b.

Connect the EGR cooler assembly to the EGR valve assembly with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 4.CONNECT ENGINE WIRE

a.

Attach the 2 wire harness clamps to connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the EGR valve assembly connector.


d.
A405761C01
1.531,1.302 1.729,0.885 1.729,0.885 1.948,0.885 true 0.99,1.969 1.24,1.969 1.24,1.969 1.406,1.552 true 1.969,0.802 2.208,0.979 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Attach the 3 hose clamps to connect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


Hide 5.ADD ENGINE COOLANT (for Engine)

Hide 6.INSPECT FOR COOLANT LEAK (for Engine)