Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E448109E03
1.365,0.5 2.094,0.708 0.729,0.208 10 false 2 0.875,1.458 1.49,1.656 0.615,0.198 10 false UDO+ 0.906,2.219 1.521,2.417 0.615,0.198 10 false UJSS 5.906,2.219 6.521,2.417 0.615,0.198 10 false USG1 5.906,1.458 6.521,1.656 0.615,0.198 10 false US1+ 5.906,0.656 6.521,0.854 0.615,0.198 10 false US1- 0.302,2.677 1.583,3.073 1.281,0.396 10 false G132 0.292,2.844 1.448,3.323 1.156,0.479 10 false No. 1 Stereo Jack Adapter Assembly 2.479,3.271 5.083,3.5 2.604,0.229 10 false : Data Signal (USB Communication Line) 1.854,2.969 3.073,3.24 1.219,0.271 10 false *: Shielded 5.813,2.635 6.427,2.833 0.615,0.198 10 false G106 5.802,2.802 7,3.271 1.198,0.469 10 false Radio and Display Receiver Assembly 5.708,0.531 5.885,0.708 0.177,0.177 10 false 2 1.344,1.313 2.219,1.5 0.875,0.188 10 false 3 1.354,2.094 2.208,2.281 0.854,0.188 10 false 5 5.708,2.094 5.885,2.271 0.177,0.177 10 false 5 5.708,1.302 5.885,1.479 0.177,0.177 10 false 3 0.906,0.656 1.521,0.854 0.615,0.198 10 false UDO- 3.563,1.802 4.781,2.073 1.219,0.271 10 false *

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
E424937C53
1.49,0.177 1.917,0.448 0.427,0.271 1.521,1.917 1.969,2.188 0.448,0.271 1.25,1.333 1.625,1.021 true 2.229,0.948 1.771,0.99 true 2.188,1.313 1.75,1.146 true 1.177,3.031 1.625,2.802 true 1.781,2.792 2.208,2.885 true 1.75,2.938 2.115,3.125 true 0.292,0.219 0.5,0.417 0.208,0.198 10 false *a 0.323,2.094 0.531,2.292 0.208,0.198 10 false *b 1.542,0.229 1.969,0.396 0.427,0.167 10 false G106 1.583,1.958 1.938,2.125 0.354,0.167 10 false G132 0.896,1.333 1.281,1.51 0.385,0.177 10 false US1+ 2.302,0.875 2.719,1.042 0.417,0.167 10 false US1- 2.25,1.26 2.667,1.427 0.417,0.167 10 false USG1 0.75,2.979 1.177,3.146 0.427,0.167 10 false UDO+ 2.25,2.813 2.646,2.969 0.396,0.156 10 false UDO- 2.146,3.094 2.563,3.26 0.417,0.167 10 false USSS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the G106 radio and display receiver assembly connector.


b.

Disconnect the G132 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G106-2 (US1-) - G132-2 (UDO-) Always Below 1 Ω
G106-3 (US1+) - G132-3 (UDO+) Always Below 1 Ω
G106-5 (USG1) - G132-5 (UJSS) Always Below 1 Ω
G106-2 (US1-) - Body ground Always 10 kΩ or higher
G106-3 (US1+) - Body ground Always 10 kΩ or higher
G106-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR