Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2020.08
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0474531 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus:

i.

Body Electrical / Main Body / Data List.


ii.

Body Electrical / Front Recognition Camera (Front Lighting Control) / Data List.


iii.

Chassis / Front Recognition Camera / Data List.



e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal OFF or ON OFF: Auto high beam switch not pressed
ON: Auto high beam switch pressed
-
Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx or SensorFail Value is output according to ambient light level -
Light Sensor Connection Status Light control sensor connection status OFF or ON OFF: Automatic light control sensor has not been connected
ON: Automatic light control sensor connected or has been connected
-
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning.
Auto H Beam STS1 Automatic high beam sensor state past 1 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS2 Automatic high beam sensor state past 2 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS3 Automatic high beam sensor state past 3 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS4 Automatic high beam sensor state past 4 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS5 Automatic high beam sensor state past 5 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS6 Automatic high beam sensor state past 6 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
Auto H Beam STS7 Automatic high beam sensor state past 7 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed* Although this item is displayed on the GTS, it is not applicable to this vehicle.
The Number of DTC Number of trouble codes 0 to 255 Number of stored DTCs displayed -
HINT:

*: The details of each value of the Range are as follows:

Display Value Condition Control Condition Diagnostic Note
Undetec Automatic high beam sensor being initialized Control suspended (low beam headlights illuminated) -
CAM NA Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. Control suspended (low beam headlights illuminated) -
No sens No lights detected High beam headlights illuminated Only when vehicle speed within operation speed range
Hlight Headlights of oncoming vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Taillgt Taillights preceding vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Speed No lights detected and vehicle speed below operation speed Low beam headlights illuminated -
Daytime Bright light detected Low beam headlights illuminated -
Village Streetlights, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Delay Changing between low beams and high beams Changing between low beams and high beams Only when vehicle speed within operation speed range
SAE Mod Not applicable - -
Malfunc
Aim Lmt
Undefin
LIN Err


Body Electrical > Front Recognition Camera (Front Lighting Control) > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Actual driving distance 0 to 16777215 Roughly the same as the actual driving distance -
Total Distance Traveled - Unit Actual driving distance unit km or mile Displays the current actual driving distance unit -
AHB/AHS Information Lighting system state unknown, AHB or AHS Displays lighting system state -
Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Recognition Camera High Temperature 2 Whether high temperature malfunction of forward recognition camera exists or not Not High Temperature or High Temperature Not High Temperature: Approximately 65°C (149°F) or less
High Temperature: Approximately 65°C (149°F) or higher
If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.
HINT:

In summertime, the windshield glass may reach 100°C (212°F) or higher




ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus:

i.

Body Electrical / Main Body / Active Test.



e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Switch Light Auto high beam switch indicator light OFF or ON -