Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E27
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was stored.
    2. 1 data set when the DTC was stored.
    3. 1 data set after the DTC was stored.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA

Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If approximately 0.0 g/sec.:
  1. Mass air flow meter power source circuit open or short.
  1. VG circuit open or short.
If 160.0 g/sec. or more:
  1. E2G circuit open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Intake Air
Intake air temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No.2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle position
-
Throttle Motor DUTY
Throttle motor
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
Vacuum Pump
Key-off EVAP system leak detection pump status
Refer to EVAP System (Click here).
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Value
Key-off EVAP system vent valve status
-
EVAP Purge VSV
EVAP Purge VSV
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at A/F sensor
-
AF Lambda B2S1
Fuel trim at A/F sensor
-
AFS Voltage B1S1
AFS Voltage B2S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Current B1S1
A/F sensor current
-
AFS Current B2S1
A/F sensor current
-
O2S B1S2
O2S B2S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S Impedance B1S2
O2S Impedance B2S2
Sub heated oxygen sensor impedance (for Sensor 2)
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
  3. OL Drive: Open loop due to driving conditions (fuel enrichment).
  4. OL Fault: Open loop due to detected system fault.
  5. CL Fault: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning.
Fuel System Status #2
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
  3. OL Drive: Open loop due to driving conditions (fuel enrichment).
  4. OL Fault: Open loop due to detected system fault.
  5. CL Fault: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning.
Air pump pressure (absolute)
Air pump pressure
-
Air Pump2 Pressure (Absolute)
Air pump pressure
-
Air Pump Pulsation Pressure
Air pump pulsation pressure
-
Air Pump2 Pulsation Pressure
Air pump pulsation pressure
-
Secondary Air Control VSV
Secondary air injection system status
-
2nd Air System Status
Second air system status
-
AI Test
Secondary air injection system operation prohibit
-
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
Catalyst Temp B1S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B2S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B1S2
Estimated catalyst temperature (for Sensor 2)
-
Catalyst Temp B2S2
Estimated catalyst temperature (for Sensor 2)
-
Starter Signal
Starter switch (STSW) signal
-
Starter Control
Starter switch status
-
Power Steering Signal Record
Power steering switch status
-
Starter Relay
Starter relay status
-
Power Steer. Sig. Record
Power steering signal (history)
This signal status is usually ON until the cables are disconnected from the battery terminals.
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/Neutral position (PNP) switch signal
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleard DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire
Only displayed during idling.
Cylinder #2 Misfire Count
Cylinder #2 misfire
Only displayed during idling.
Cylinder #3 Misfire Count
Cylinder #3 misfire
Only displayed during idling.
Cylinder #4 Misfire Count
Cylinder #4 misfire
Only displayed during idling.
Cylinder #5 Misfire Count
Cylinder #5 misfire
Only displayed during idling.
Cylinder #6 Misfire Count
Cylinder #6 misfire
Only displayed during idling.
Cylinder #7 Misfire Count
Cylinder #7 misfire
Only displayed during idling.
Cylinder #8 Misfire Count
Cylinder #8 misfire
Only displayed during idling.
All Cylinders Misfire Count
All cylinders misfire
Only displayed during idling.
Multi Cylinders Misfire Count
Multiple cylinder misfire
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Catalyst over temperature misfire prevention F/C
-
Cat OT MF F/C History
Catalyst over temperature misfire prevention F/C history
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#7
Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#8
Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)
-
Power Steering Pressure
Power steering pressure sensor
-
ACT VSV
A/C cut status for Active Test
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and engine speed over 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
SPD (NT)
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed
-