DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) |
DTC P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Camshaft Bank 1) signal (2 trip detection logic) |
|
| P0017 | Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Camshaft Bank 1) signal (2 trip detection logic) |
|
| P0018 | Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Camshaft Bank 2) signal (2 trip detection logic) |
|
| P0019 | Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Camshaft Bank 2) signal (2 trip detection logic) |
|
| Related DTCs | P0016: Camshaft timing misalignment at idling (Bank 1 Intake Side) P0017: Camshaft timing misalignment at idling (Bank 1 Exhaust Side) P0018: Camshaft timing misalignment at idling (Bank 2 Intake Side) P0019: Camshaft timing misalignment at idling (Bank 2 Exhaust Side) |
| Required Sensors/Components | VVT actuator |
| Required Sensors/Components | Camshaft position sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 1 minute |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil Control Valve) P0016, P0018 (VVT System - Misalignment) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) |
| VVT feedback mode | Executing |
| VVT | Maximum retarded position |
| Engine speed | 400 to 1400 rpm |
| Monitor runs whenever following DTCs not present | P0013, P0023 (Exhaust VVT Oil Control Valve) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) |
| VVT feedback mode | Executing |
| VVT | Maximum advanced position |
| Engine speed | 400 to 1400 rpm |
| One of following conditions met | - |
| VVT learning value | Less than 22.23°CA |
| VVT learning value | More than 46.68°CA |
| One of following conditions met | - |
| VVT learning value | Less than 82.23°CA |
| VVT learning value | More than 106.68°CA |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0016, P0017, P0018 or P0019 is output | A |
| P0016, P0017, P0018 or P0019 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY |
![]() ![]() |
Remove the OCV.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Apply positive (+) battery voltage to terminal 1 and negative (-) battery voltage to terminal 2. Check the valve operation.
|
| ||||
| OK | |
| 5.REPLACE CAMSHAFT TIMING GEAR |
Replace the camshaft timing gear (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTC (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the Techstream (Click here).
Drive the vehicle in an urban area for approximately 10 minutes.
Read DTCs using the Techstream.
|
| ||||
| OK | ||
| ||