Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0120 .

DTC No.
DTC Detection Condition
Trouble Area
P0121
Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds
(1 trip detection logic)
TP sensor (built into throttle body)

MONITOR DESCRIPTION

The ECM uses the TP sensor to monitor the throttle valve opening angle.
This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the TP sensor and VTA1.
For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the TP sensor. The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0121: TP sensor rationality
Required Sensors/Components (Main)
TP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
Within 2 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0120, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
Either of following conditions A or B set
-
A. Ignition switch
ON
B. Electric throttle motor power
ON

TYPICAL MALFUNCTION THRESHOLDS


Difference in voltage between VTA1 and VTA2
TP sensor 1 - [TP sensor 2 x 0.8 (corrected by learning value)]
Less than 0.8 V, or more than 1.6 V

FAIL-SAFE

When this DTC, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

INSPECTION PROCEDURE

HINT:
  1. This DTC relates to the Throttle Position (TP) sensor.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0121 is output
    A
    P0121 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A

REPLACE THROTTLE BODY ASSEMBLY (Click here)