Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2119    Throttle Actuator Control Throttle Body Range / Performance

for Preparation Click here


DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, Throttle Position (TP) sensor, Accelerator Pedal Position (APP) sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The TP sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
  1. ETCS
  2. ECM

MONITOR DESCRIPTION

The ECM determines the actual opening angle of the throttle valve from the TP sensor signal. The actual opening angle is compared to the target opening angle commanded by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by the accelerator pedal being fully depressed (fully open the throttle valve).

MONITOR STRATEGY


Related DTCs
P2119: ETCS malfunction
Required Sensors/Components (Main)
Throttle actuator
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
Within 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
System guard*
ON
System guard is ON when the following conditions set
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or higher
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


Either of following conditions A or B met
-
A. Difference between commanded closed throttle position and current closed throttle position
0.3 V or more for 1 second
B. Difference between commanded open throttle position and current open throttle position
0.3 V or more for 0.6 seconds

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2119 is output
    A
    P2119 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2119 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Allow the engine to idle for 15 seconds.

    CAUTION:
    Exercise extreme care and take precautions in procedure "A" and "B" below. Failure to do so may result in the vehicle unexpectedly rolling away.

  1. Securely apply the parking brake and move the shift lever to D (Procedure "A").

  1. While depressing the brake pedal securely, fully depress the accelerator pedal for 5 seconds (Procedure "B").

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.

    HINT:
    The output voltage of the throttle position sensor can be checked during procedure "B" using the Techstream. Variations in the output voltage indicate that the throttle actuator is in operation. To check the output voltage using the Techstream, enter the following menus: Powertrain / Engine / ETCS / Throttle Position No. 1.

    OK:
    No DTC is output.



NG
REPLACE THROTTLE BODY ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)