Home › Engine / Hybrid System ยท 3UR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


    A149190E01
  1. Apply gasoline or spindle oil to a new O-ring and install it to the injector.

    NOTICE:
    Make sure that there is no damage or foreign material in the groove of the injector when installing the O-ring.



    A161427E01
  1. Connect the injector connector.



    A161479E01
  1. Install the injector to the fuel delivery pipe as shown in the illustration.

    NOTICE:
    1. Make sure that there are no scratches or foreign matter in or around the insertion hole of the fuel delivery pipe.
    2. When inserting the injector, be careful not to damage the O-ring.
    3. Attach the part of the injector labeled B between the parts of the fuel delivery pipe labeled A.



    A161480E02
  1. Check that each injector is installed to the fuel delivery pipe facing the direction shown in the illustration.



2. INSTALL NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY


    A161425
  1. Install the 2 spacers and 4 insulators to the cylinder head LH.

  1. Install the fuel delivery pipe (with injectors) to the cylinder head LH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


    NOTICE:
    A163659E01
    Make sure that the part of the injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 6 wire harness connector.



3. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Install the No. 1 engine cover.



4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A161424
  1. Install the 2 spacers and 4 insulators to the cylinder head RH.

  1. Install the fuel delivery pipe (with injectors) to the cylinder head RH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


    NOTICE:
    A163659E01
    Make sure that the part of the injector labeled B is between the parts of the fuel delivery pipe labeled A.



5. INSTALL NO. 3 ENGINE COVER
  1. Install the No. 3 engine cover.



6. CONNECT NO. 3 VENTILATION HOSE


    A161422
  1. Connect the No. 7 wire harness connector.

  1. Connect the No. 3 ventilation hose.



7. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A161416
  1. Connect the No. 1 fuel pipe to the No. 2 fuel delivery pipe (Click here).



8. CONNECT FUEL TUBE SUB-ASSEMBLY


    A161415
  1. Connect the fuel tube to the No. 2 fuel delivery pipe (Click here).



    A161417
  1. Connect the fuel tube to the fuel delivery pipe (Click here).



9. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A161418
  1. Connect the No. 2 fuel tube to the fuel pressure regulator (Click here).



10. INSTALL AIR CLEANER HOSE ASSEMBLY


A187008
  1. Install the air cleaner hose with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the ventilation hose.



11. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch ON.

    NOTICE:
    Do not start the engine.

  1. Techstream:
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



12. INSTALL V-BANK COVER


A165576E03
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.