CYLINDER BLOCK > DISASSEMBLY |
| 1. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 2. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
Remove the 2 connecting rod cap bolts.
![]() |
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches. If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
![]() |
Install the connecting rod cap with the 2 bolts.
![]() |
Mark the front side of each connecting rod cap bolt with paint.
Tighten the cap bolts an additional 90° as shown.
Check that the painted marks are now at a 90° angle to the front.
Remove the 2 bolts, connecting rod cap and lower bearing.
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Connecting rod | Crankshaft | Use bearing |
| Number Mark | 1 | 1 | 2 |
| 2 | 3 | ||
| 2 | 1 | ||
| 1 | 3 | 4 | |
| 2 | 2 | ||
| 3 | 1 | ||
| 2 | 3 | 5 | |
| 3 | 2 | ||
| 4 | 1 | ||
| 3 | 3 | 6 | |
| 4 | 2 | ||
| 3 | 7 |
| Number Mark | Specified Condition |
| Mark 1 | 55.000 to less than 55.006 mm (2.1654 to less than 2.1656 in.) |
| Mark 2 | 55.006 to less than 55.012 mm (2.1656 to less than 2.1658 in.) |
| Mark 3 | 55.012 to less than 55.018 mm (2.1658 to less than 2.1661 in.) |
| Mark 4 | 55.018 to less than 55.024 mm (2.1661 to less than 2.1663 in.) |
| Number Mark | Specified Condition |
| Mark 1 | 51.994 to less than 52.000 mm (2.0470 to less than 2.0472 in.) |
| Mark 2 | 51.988 to less than 51.994 mm (2.0468 to less than 2.0470 in.) |
| Mark 3 | 51.982 to less than 51.988 mm (2.0465 to less than 2.0468 in.) |
| Number Mark | Specified Condition |
| Mark 2 | 1.487 to less than 1.490 mm (0.0585 to less than 0.0587 in.) |
| Mark 3 | 1.490 to less than 1.493 mm (0.0587 to less than 0.0588 in.) |
| Mark 4 | 1.493 to less than 1.496 mm (0.0588 to less than 0.0589 in.) |
| Mark 5 | 1.496 to less than 1.499 mm (0.0589 to less than 0.0590 in.) |
| Mark 6 | 1.499 to less than 1.502 mm (0.0590 to less than 0.0591 in.) |
| Mark 7 | 1.502 to less than 1.505 mm (0.0591 to less than 0.0593 in.) |
Completely remove the Plastigage.
Perform the inspection above for each cylinder.
| 3. REMOVE PISTON AND CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Remove the 16 cap bolts and 8 connecting rod caps.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 4. REMOVE CONNECTING ROD BEARING |
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
| 5. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 6. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.
![]() |
Using 2 screwdrivers, gradually pry up and remove the 5 crankshaft bearing caps, 5 lower bearings and 2 lower thrust washers (No. 3 crankshaft bearing cap only).
Lift out the crankshaft.
Remove the 2 upper thrust washers.
Clean each crankshaft journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Examine the front marks and number, and install the 5 crankshaft bearing caps to the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.
![]() |
Install and uniformly tighten the 10 crankshaft bearing cap bolts in several steps, in the order shown in the illustration.
![]() |
Mark the front of the crankshaft bearing cap bolts with paint.
Tighten the crankshaft bearing cap bolts an additional 90° in the order shown above.
Check that the painted marks are now at a 90° angle to the front.
Remove the crankshaft bearing caps and bolts.
![]() |
Measure the Plastigage at its widest point.
| Number Mark | Specified Condition |
| No. 1 and No. 5 | 0.028 to 0.046 mm (0.00110 to 0.00181 in.) |
| Others | 0.040 to 0.058 mm (0.00157 to 0.00228 in.) |
![]() |
| (A) + (B) | Use Bearing | |
| Upper | Lower | |
| 0 to 5 | 3 | 3 |
| 6 to 8 | 3 | 4 |
| 9 to 11 | 4 | 4 |
| 12 to 14 | 4 | 5 |
| 15 to 17 | 5 | 5 |
| 18 to 20 | 5 | 6 |
| 21 to 23 | 6 | 6 |
| 24 to 26 | 6 | 7 |
| 27 to 28 | 7 | 7 |
| (A) + (B) | Use Bearing | |
| Upper | Lower | |
| 0 to 5 | 1 | 1 |
| 6 to 8 | 1 | 2 |
| 9 to 11 | 2 | 2 |
| 12 to 14 | 2 | 3 |
| 15 to 17 | 3 | 3 |
| 18 to 20 | 3 | 4 |
| 21 to 23 | 4 | 4 |
| 24 to 26 | 4 | 5 |
| 27 to 28 | 5 | 5 |
| Number Mark | Specified Condition |
| Mark 00 | 72.000 mm (2.83464 in.) |
| Mark 01 | 72.001 mm (2.83469 in.) |
| Mark 02 | 72.002 mm (2.83472 in.) |
| Mark 03 | 72.003 mm (2.83476 in.) |
| Mark 04 | 72.004 mm (2.83480 in.) |
| Mark 05 | 72.005 mm (2.83484 in.) |
| Mark 06 | 72.006 mm (2.83488 in.) |
| Mark 07 | 72.007 mm (2.83492 in.) |
| Mark 08 | 72.008 mm (2.83496 in.) |
| Mark 09 | 72.009 mm (2.83500 in.) |
| Mark 10 | 72.010 mm (2.83503 in.) |
| Mark 11 | 72.011 mm (2.83508 in.) |
| Mark 12 | 72.012 mm (2.83512 in.) |
| Mark 13 | 72.013 mm (2.83516 in.) |
| Mark 14 | 72.014 mm (2.83520 in.) |
| Mark 15 | 72.015 mm (2.83524 in.) |
| Mark 16 | 72.016 mm (2.83528 in.) |
| Number Mark | Specified Condition |
| Mark 00 | 67.000 mm (2.63780 in.) |
| Mark 01 | 66.999 mm (2.63775 in.) |
| Mark 02 | 66.998 mm (2.63771 in.) |
| Mark 03 | 66.997 mm (2.63768 in.) |
| Mark 04 | 66.996 mm (2.63763 in.) |
| Mark 05 | 66.995 mm (2.63760 in.) |
| Mark 06 | 66.994 mm (2.63756 in.) |
| Mark 07 | 66.993 mm (2.63751 in.) |
| Mark 08 | 66.992 mm (2.63748 in.) |
| Mark 09 | 66.991 mm (2.63744 in.) |
| Mark 10 | 66.990 mm (2.63740 in.) |
| Mark 11 | 66.989 mm (2.63736 in.) |
| Mark 12 | 66.988 mm (2.63732 in.) |
| Number Mark | Specified Condition |
| Mark 3 | 2.487 to less than 2.490 mm (0.0979 to less than 0.0980 in.) |
| Mark 4 | 2.490 to less than 2.493 mm (0.0980 to less than 0.0981 in.) |
| Mark 5 | 2.493 to less than 2.496 mm (0.0981 to less than 0.0983 in.) |
| Mark 6 | 2.496 to less than 2.499 mm (0.0983 to less than 0.0984 in.) |
| Mark 7 | 2.499 to less than 2.502 mm (0.0984 to less than 0.0985 in.) |
| Number Mark | Specified Condition |
| Mark 1 | 2.481 to less than 2.484 mm (0.0977 to less than 0.0978 in.) |
| Mark 2 | 2.484 to less than 2.487 mm (0.0978 to less than 0.0979 in.) |
| Mark 3 | 2.487 to less than 2.490 mm (0.0979 to less than 0.0980 in.) |
| Mark 4 | 2.490 to less than 2.493 mm (0.0980 to less than 0.0981 in.) |
| Mark 5 | 2.493 to less than 2.496 mm (0.0981 to less than 0.0983 in.) |
Completely remove the Plastigage.
| 7. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the crankshaft bearings and upper thrust washers from the cylinder block.
| 8. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the No. 1 and No. 2 piston rings.
Remove the oil ring (2 side rails and expander) by hand.
| 9. REMOVE PISTON SUB-ASSEMBLY WITH PIN |
![]() |
Check the fitting condition between the piston and piston pin.
Move the connecting rod back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
Rotate the piston back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
![]() |
Using a small screwdriver, pry out the 2 snap rings.
![]() |
Gradually heat the piston to approximately 60°C (140°F).
![]() |
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod.
| 10. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.