Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL REAR CRANKSHAFT OIL SEAL


    A054148E02
  1. Place the oil seal retainer on wooden blocks.

  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-56010  

  1. Apply MP grease to the lip of the oil seal.



2. INSTALL REAR ENGINE OIL SEAL RETAINER


    A123317E03
  1. Apply seal packing to the oil seal retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Install the oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the oil seal retainer and cylinder block.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A123318E01
  1. Install a new O-ring to the cylinder block.

  1. Install the oil seal retainer with the 7 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL FRONT CRANKSHAFT OIL SEAL


    A054146E02
  1. Place the oil pump on a wooden block.

  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump body edge.

    SST
    09316-60011  

  1. Apply MP grease to the lip of the oil seal.



4. INSTALL OIL PUMP ASSEMBLY


    A150127
  1. Apply a light coat of engine oil to a new O-ring and install it to the cylinder block.



    A120236E01
  1. Apply seal packing to the oil pump as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Install the oil pump within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the oil pump and cylinder block.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A150128
  1. Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and oil pump to the crankshaft.



    A120049E03
  1. Install the oil pump with the 7 standard bolts and 6 mm hexagon wrench bolt. Uniformly tighten the bolts in several steps.

    1. for bolt A, B, C, E

    Torque:
    16 N*m{ 158 kgf*cm , 11 ft.*lbf }

    1. for bolt D

    Torque:
    31 N*m{ 311 kgf*cm , 23 ft.*lbf }

    Bolt Length:
    Item
    Bolt Head Size
    Length
    Bolt A
    12 mm
    35 mm (1.38 in.)
    Bolt B
    12 mm
    50 mm (1.97 in.)
    Bolt C
    14 mm
    103 mm (4.06 in.)
    Bolt D
    14 mm
    44 mm (1.73 in.)
    Bolt E
    6 mm hexagon
    28 mm (1.10 in.)



5. INSTALL OIL STRAINER SUB-ASSEMBLY


    A150116
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL NO. 3 OIL PAN BAFFLE PLATE
  1. Install the baffle plate with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



7. INSTALL NO. 2 OIL PAN BAFFLE PLATE
  1. Install the baffle plate with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



8. INSTALL NO. 1 OIL PAN BAFFLE PLATE
  1. Install the baffle plate with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



9. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG).

    1. Using a gasket scraper, remove all the old packing (FIPG) from the gasket surfaces and sealing groove. Thoroughly clean all components.

    2. Using a non-residue solvent, clean both sealing surfaces.



    A150129E01
  1. Apply seal packing to the No. 1 oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 5.0 mm (0.118 to 0.197 in.)

    NOTICE:
    1. Install the oil pan within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the oil pan and cylinder block.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A176468E04
  1. Temporarily install the No. 1 oil pan with the 18 bolts, 2 nuts.

    Bolt Length:
    Item
    Bolt Head Size
    Length
    Bolt A
    10 mm
    22 mm (0.866 in.)
    Bolt B
    12 mm
    25 mm (0.984 in.)
    Bolt C
    12 mm
    60 mm (2.36 in.)
    Bolt D
    10 mm
    35 mm (1.38 in.)

    NOTICE:
    Make sure the rear ends of the No. 1 oil pan and cylinder block are aligned. If not, the oil pan may become damaged.

  1. Uniformly tighten the bolts and nuts in several passes.

    1. for bolt A, D, E

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    1. for bolt B, C, nut

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



10. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    A150130E01
  1. Apply seal packing to the No. 2 oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 5.0 mm (0.118 to 0.197 in.)

    NOTICE:
    1. Install the oil pan within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the No. 1 oil pan and No. 2 oil pan.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A176467E03
  1. Install the No. 2 oil pan with the 8 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several passes.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



11. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY


    A176466
  1. Install a new gasket to the oil filter bracket.

  1. Install the oil filter bracket with the 2 bolts and nut.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    A178867
  1. Connect the oil cooler hoses to the oil cooler.

  1. Connect the oil pressure sender gauge connector.



12. INSTALL OIL FILTER ASSEMBLY


    A150110
  1. Clean and check the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.



    A150111E01
  1. Using SST, tighten the oil filter. Depending on the work space available, choose from the following.

    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or with a common wrench.



13. INSTALL WATER PUMP ASSEMBLY


    A122970E01
  1. Install a new O-ring to the water by-pass pipe.

  1. Apply soapy water to the O-ring.

  1. Connect the water pump to the water by-pass pipe end.

  1. Temporarily install the water pump and a new gasket with the 5 bolts, 2 stud bolts and nut. Uniformly tighten the bolts, stud bolts and nut in several passes.

    1. for Bolt

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    1. for Stud bolt, nut

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }



14. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    A123319E01
  1. Apply seal packing to 2 or 3 threads of the drain cock.

    Seal packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent



    A160807E01
  1. Install the 2 drain cocks as shown in the illustration.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    1. Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.
    2. Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.



15. INSTALL NO. 2 CYLINDER HEAD GASKET


    A160768
  1. Clean the cylinder block and cylinder head with solvent.

  1. Place a new cylinder head gasket in position on the cylinder block.

    HINT:
    A mark is placed on the rear side of the cylinder head gasket to distinguish the LH and RH sides, a "2R" mark for the RH side and a "2L" mark for the LH side.

    NOTICE:
    Be careful of the installation direction.



16. INSTALL CYLINDER HEAD LH


    G039657E01
  1. Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration, and that the piston is below the TDC of compression.

  1. Install the cylinder head with the exhaust manifold to the cylinder block.

    NOTICE:
    Ensure that no oil is on the mounting surface of the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Set the plate washer to the cylinder head bolt.



    A115101E04
  1. Install and uniformly tighten the 10 cylinder head bolts and plate washers in the sequence shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

    NOTICE:
    Do not drop the plate washer for the cylinder head bolt into portion A of the cylinder head. If dropped into portion A, the plate washer will pass through the cylinder head and cylinder block into the oil pan.



    A115112E02
  1. Mark the cylinder head bolt head with paint as shown in the illustration.

  1. Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.

  1. Check that the painted marks are now facing rearward.



17. INSTALL CYLINDER HEAD GASKET


    A160769
  1. Clean the cylinder block and cylinder head with solvent.

  1. Place a new cylinder head gasket in position on the cylinder block.

    HINT:
    A mark is placed on the rear side of the cylinder head gasket to distinguish the LH and RH sides, a "2R" mark for the RH side and a "2L" mark for the LH side.

    NOTICE:
    Be careful of the installation direction.



18. INSTALL CYLINDER HEAD SUB-ASSEMBLY


    G039657E01
  1. Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration, and that the piston is below the TDC of compression.

  1. Install the cylinder head with the exhaust manifold to the cylinder block.

    NOTICE:
    Ensure that no oil is on the mounting surface of the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Set the plate washer to the cylinder head bolt.



    A115100E03
  1. Install and uniformly tighten the 10 cylinder head bolts and plate washers in the sequence shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

    NOTICE:
    Do not drop the plate washer for the cylinder head bolt into portion A of the cylinder head. If dropped into portion A, the plate washer will pass through the cylinder head and cylinder block into the oil pan.



    A115112E02
  1. Mark the cylinder head bolt head with paint as shown in the illustration.

  1. Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.

  1. Check that the painted marks are now facing rearward.



19. INSTALL VALVE LIFTER
  1. Apply a light coat of engine oil to the valve lifters and shims.

  1. Install the valve lifters and shims.

  1. Check that the valve lifter rotates smoothly by hand.



20. INSTALL CAMSHAFT SETTING OIL SEAL


    A118107E01
  1. Insert 2 new oil seals into the camshaft timing tube until they reach the stopper.

    NOTICE:
    1. Be careful of the installation direction.
    2. Do not turn over the lip of the oil seal.



21. INSTALL CAMSHAFT TIMING TUBE ASSEMBLY


    A054965E05
  1. Align the timing tube knock pin with the knock pin groove of the drive gear, and temporarily install the drive gear with the 4 bolts.

  1. Using SST and a 5 mm hexagon wrench, uniformly tighten the 4 bolts in several steps.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    SST
    09960-10010   (09962-01000, 09963-00500)

    NOTICE:
    Be careful not to damage the timing tube.



    A054967E01
  1. Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    Be careful not to damage the camshaft.



    A118091E01
  1. Align the camshaft knock pin with the knock pin groove of the timing tube, and push the timing tube by hand until it touches the bottom.

  1. Using a 10 mm hexagon wrench, install the bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Install the seal washer and screw plug.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



22. INSTALL CAMSHAFT SUB-GEAR


    A054971E01
  1. Install the gear spring [1], sub-gear [2] and wave washer [3].

    HINT:
    Attach the pins on the gears to the gear spring ends.



    A054970E01
  1. Using snap ring pliers, install the snap ring.



    A054968E01
  1. Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    Be careful not to damage the camshaft.



    A054972E03
  1. Using SST, align the holes of the driven main gear and sub-gear by turning the sub-gear clockwise, and temporarily install a service bolt.

    SST
    09960-10010   (09962-01000, 09963-00500)

    Recommended Service Bolt:
    Thread Diameter
    Thread Pitch
    Bolt Length
    6 mm
    1.0 mm
    16 to 20 mm (0.630 to 0.787 in.)

  1. Align the gear teeth of the driven main gear and sub-gear, and tighten the service bolt.



23. INSTALL CAMSHAFT (for Bank 2)

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged. To avoid this, the following steps should be carried out.

HINT:
When performing this procedure to adjust the valve clearance, it is not necessary to apply seal packing to the No. 5 bearing cap and camshaft housing plug.



    A134393E04
  1. Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration, and that the piston is below the TDC of compression.

    NOTICE:
    Having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft. Always set the crankshaft pulley at the correct angle as shown in the illustration.

  1. Apply a light coat of engine oil to the cam lobe and gear of the camshaft and also the journal of the cylinder head.



    A118093E01
  1. Using a wrench, align the timing marks (1 dot marks each) of the camshaft drive and driven main gears, and set the No. 1 and No. 2 camshafts in place.



  1. Install the bearing cap.



      A054975E01
    1. Apply seal packing to the camshaft housing plug groove.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      HINT:
      Remove any old packing (FIPG) material before applying new seal packing.



    2. A118102
    3. Install the camshaft housing plug and oil control valve filter to the cylinder head as shown in the illustration.

      NOTICE:
      1. Be careful of the installation direction.
      2. Remove any oil from the contact surface.



    4. A054356E03
    5. Apply seal packing to the No. 1 bearing cap as shown in the illustration.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Standard seal diameter:
      1.5 to 2.0 mm (0.0591 to 0.0787 in.)

      NOTICE:
      1. Do not apply seal packing to the front bearing cap grooves.
      2. Install the No. 1 bearing cap and housing plug within 3 minutes.



    6. A118094E04
    7. Install 4 new seal washers to the bearing cap bolts (A and B).

    8. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts (C to E).

      NOTICE:
      Do not apply engine oil to the bearing cap bolts (A and B).



    9. A118103
    10. Temporarily install the oil feed pipe and bearing caps with the 22 bolts, as shown in the illustration.

      Bolt Length:
      Item
      Length
      Bolt A with seal washer
      94 mm (3.70 in.)
      Bolt B with seal washer
      72 mm (2.84 in.)
      Bolt C
      25 mm (0.984 in.)
      Bolt D
      55 mm (2.17 in.)
      Bolt E
      40 mm (1.58 in.)



    11. A118104E01
    12. Push in the camshaft setting oil seal.



    13. A118094E05
    14. Uniformly tighten the 22 bearing cap bolts in several steps, in the sequence shown in the illustration.

      1. for bolt 21, 22

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

      1. for other bolt

      Torque:
      16 N*m{ 163 kgf*cm , 12 ft.*lbf }



    A118092E01
  1. Bring the service bolt installed in the driven sub-gear upward by turning the hexagonal portion of the camshaft with a wrench.

  1. Remove the service bolt.



24. INSTALL CAMSHAFT SUB-ASSEMBLY (for Bank 1)

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged. To avoid this, the following steps should be carried out.

HINT:
When performing this procedure to adjust the valve clearance, it is not necessary to apply seal packing to the No. 5 bearing cap and camshaft housing plug.



    A134393E04
  1. Check that the timing mark of the crankshaft timing pulley is in the position shown in the illustration, and that the piston is below the TDC of compression.

    NOTICE:
    Having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft. Always set the crankshaft pulley at the correct angle as shown in the illustration.

  1. Apply a light coat of engine oil to the cam lobe and gear of the camshaft and also the journal of the cylinder head.



    A118105
  1. Using a wrench, align the timing marks (2 dot marks each) of the camshaft drive and driven main gears, and set the No. 3 and No. 4 camshafts in place.



  1. Install the bearing cap.



      A054975E01
    1. Apply seal packing to the camshaft housing plug groove.

      HINT:
      Remove any old packing (FIPG) material before applying new seal packing.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent



    2. A118095
    3. Install the camshaft housing plug and oil control valve filter to the cylinder head as shown in the illustration.

      NOTICE:
      1. Be careful of the installation direction.
      2. Remove any oil from the contact surface.



    4. A054357E03
    5. Apply seal packing to the No. 1 bearing cap as shown in the illustration.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Standard seal diameter:
      1.5 to 2.0 mm (0.0591 to 0.0787 in.)

      NOTICE:
      1. Do not apply seal packing to the front bearing cap grooves.
      2. Install the No. 1 bearing cap and housing plug within 3 minutes.



    6. A118099E05
    7. Install 4 new seal washers to the bearing cap bolts (A and B).

    8. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts (C to E).

      NOTICE:
      Do not apply engine oil to the bearing cap bolts (A and B).



    9. A118096
    10. Temporarily install the oil feed pipe and bearing caps with the 22 bolts, as shown in the illustration.

      Bolt Length:
      Item
      Length
      Bolt A with seal washer
      94 mm (3.70 in.)
      Bolt B with seal washer
      72 mm (2.84 in.)
      Bolt C
      25 mm (0.984 in.)
      Bolt D
      55 mm (2.17 in.)
      Bolt E
      40 mm (1.58 in.)



    11. A118097E01
    12. Push in the camshaft setting oil seal.



    13. A118099E04
    14. Uniformly tighten the 22 bearing cap bolts in several steps, in the sequence shown in the illustration.

      1. for bolt 21, 22

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

      1. for other bolt

      Torque:
      16 N*m{ 163 kgf*cm , 12 ft.*lbf }



    A118100E01
  1. Bring the service bolt installed in the driven sub-gear upward by turning the hexagonal portion of the camshaft with a wrench.

  1. Remove the service bolt.



25. INSTALL REAR TIMING BELT PLATE RH
  1. Install the No. 1 timing belt plate and No. 2 timing belt plate with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



26. INSTALL CAMSHAFT TIMING PULLEY


A160790
  1. Align the camshaft timing tube knock pin with the knock pin groove of the timing pulley.

  1. Temporarily install the 4 bolts of the camshaft timing pulley.

  1. Hold the hexagonal portion of the camshaft with a wrench.

  1. Using a 5 mm hexagon wrench, tighten the 4 bolts.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 ft.*lbf }



27. INSTALL REAR TIMING BELT PLATE LH
  1. Install the No. 1 timing belt plate and No. 2 timing plate with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



28. INSTALL CAMSHAFT TIMING PULLEY SUB-ASSEMBLY LH


    A160789
  1. Align the camshaft timing tube knock pin with the knock pin groove of the timing pulley.

  1. Temporarily install the 4 bolts of the camshaft timing pulley.

  1. Hold the hexagonal portion of the camshaft with a wrench.

  1. Using a 5 mm hexagon wrench, tighten the 4 bolts.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }



29. INSTALL CAMSHAFT POSITION SENSOR ASSEMBLY


    A175764
  1. Install the camshaft position sensor with the bolt and stud bolt.

    Torque:
    7.5 N*m{ 80 kgf*cm , 66 in.*lbf }



30. INSTALL CRANKSHAFT TIMING PULLEY


    A004446E02
  1. Align the timing pulley set key with the key groove of the pulley.

  1. Using SST and a hammer, tap in the timing pulley with the flange side facing inward.

    SST
    09223-46011  



31. INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY


    A072699E01
  1. Install the idler with the bolt.

    Torque:
    35 N*m{ 352 kgf*cm , 25 ft.*lbf }



32. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


A072698E01
  1. When reusing the timing belt idler shaft, apply adhesive to 2 or 3 of the threads.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 10 mm hexagon wrench, install the plate washer and idler with the bolt.

    Torque:
    35 N*m{ 352 kgf*cm , 25 ft.*lbf }



33. INSTALL TIMING BELT


    A160802E01
  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the hexagonal portion of the camshaft to align the timing marks of the camshaft timing pulleys and timing belt plates.



    2. A160751E01
    3. Using the pulley set bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.



    A160752
  1. Install the timing belt.

    1. Remove any oil or water from each pulley, and keep them clean.

      NOTICE:
      Only wipe the pulleys. Do not use any cleansing agent on the pulleys.

    2. Face the front mark (arrow) on the timing belt forward.

    3. Align the timing marks on the timing belt and crankshaft timing pulley, and the timing belt and camshaft timing pulleys, and install the timing belt.



    A054983E03
  1. Install the belt tensioner.

    1. Using a press, slowly press in the push rod using 981 to 9807 N (100 to 1000 kgf, 220.5 to 2204.7 lbf) of force.

    2. Align the holes of the push rod and housing, and pass a 1.5 mm hexagon wrench through the holes to keep the setting position of the push rod.

    3. Release the press.

    4. Install the dust boot to the belt tensioner.



    5. A160753E02
    6. Temporarily install the belt tensioner with the 2 bolts.

    7. Tighten the 2 bolts.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    8. Using pliers, remove the 1.5 mm hexagon wrench from the timing belt tensioner.



34. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION


    A160757E01
  1. Using the pulley set bolt, slowly turn the crankshaft pulley 2 revolutions from the TDC to TDC.

    NOTICE:
    Always turn the crankshaft pulley clockwise.

  1. Check that each pulley is aligned with each timing mark as shown in the illustration.
    If the timing marks are not aligned, remove the timing belt and reinstall it.

  1. Remove the pulley set bolt.



35. INSPECT VALVE CLEARANCE
  1. Inspect the valve clearance .
    If the result is not as specified, adjust the valve clearance .



36. INSTALL SPARK PLUG TUBE GASKET


    A100218E01
  1. Using a cutter knife, cut off the seal part of the removed gasket.



    A160825E01
  1. Using the removed gasket and a hammer, tap in a new gasket until it stops.

    HINT:
    If the removed gasket does not fit on the new one, correct the removed one with pliers.

  1. Apply a light coat of MP grease to the lip of the gasket.

  1. Return the 8 ventilation case claws to the original positions.



37. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    EM07143E01
  1. Apply seal packing to the semicircular plug grooves.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

  1. Install the 2 semicircular plugs to the cylinder heads.

  1. Install the gasket to the cylinder head cover.



    A116067E01
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.



    A160763
  1. Install the cylinder head cover with the 9 bolts. Uniformly tighten the bolts in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



38. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH


    EM07143E01
  1. Apply seal packing to the semicircular plug grooves.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

  1. Install the 2 semicircular plugs to the cylinder heads.

  1. Install the gasket to the cylinder head cover.



    A053978E02
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.



    A160762
  1. Install the cylinder head cover with the 9 bolts. Uniformly tighten the bolts in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



39. INSTALL OIL FILLER CAP HOUSING


    A072688E01
  1. Install a new gasket and housing with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



40. INSTALL OIL FILLER CAP SUB-ASSEMBLY


41. INSTALL SPARK PLUG


42. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A176501E01
  1. Install the sensor plate as shown in the illustration.

    NOTICE:
    Take care not to install it in a wrong direction.



43. INSTALL NO. 1 TIMING BELT COVER


    A072694E02
  1. Install the cover spacer and gasket.

  1. Install the timing belt cover with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



44. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY


A160755E01
  1. Align the pulley set key with the key groove of the crankshaft damper.

  1. Using SST, hold the crankshaft pulley and install the pulley bolt.

    Torque:
    245 N*m{ 2498 kgf*cm , 181 ft.*lbf }

    SST
    09213-70011  
    09330-00021  



45. INSTALL FAN BRACKET SUB-ASSEMBLY


A115076E02
  1. Install the fan bracket with the 2 bolts and 2 nuts.

    1. for nut A, bolt B

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    1. for nut C, bolt D

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



46. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A110456
  1. Install the idler pulley and cover plate with the bolt.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



47. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A072692E01
  1. Install the belt tensioner with the bolt and 2 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



48. INSTALL NO. 2 TIMING BELT COVER SUB-ASSEMBLY


    A054467E01
  1. Install the timing belt cover and fit the claws and pins into each part.

  1. Install the 2 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



49. INSTALL NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH


    A185277E01
  1. Pass the camshaft position sensor wire through the cover hole.

  1. Install the cover with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the wire harness grommet to the belt cover.

  1. Connect the sensor connector.

  1. Install the sensor wire to the wire clamps on the cover.

  1. Connect the engine wire to the 4 wire clamps on the cover.



50. INSTALL NO. 2 TIMING CHAIN OR BELT COVER


    A123355
  1. Install the cover with the 3 bolts and nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }