Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E161312
  1. Remove the nut and remove the wiper arm and blade assembly.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure for both sides.



4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Disengage the claw and remove the front fender to cowl side seal.



5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161315
  1. Remove the 2 clips.

  1. Remove the 6 claws and 8 guides and remove the cowl top ventilator louver sub-assembly.



7. REMOVE FRONT DOOR SCUFF PLATE RH


    B190151
  1. Detach the 9 claws and remove the scuff plate.



8. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



9. REMOVE COWL SIDE TRIM BOARD RH


    B190152
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



10. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B191803
  1. Remove the front door opening trim weatherstrip.



12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



13. REMOVE FRONT PILLAR GARNISH RH
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the 2 assist grip plugs.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B190131E01



    B190132E01
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



14. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.



15. REMOVE ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Remove the roof console box .

  1. for Long Type:
    Remove the roof console box .



16. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the lens.


    B190138E01

  1. Using a moulding remover D, disengage the 4 clips.

  1. Disconnect the connector and then remove the No. 1 room light assembly.



17. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)


    B193035E01
  1. Using a moulding remover D, disengage the 4 clips.



    B191797
  1. Disconnect the connector and then remove the No. 1 room light assembly.



18. REMOVE VISOR BRACKET COVER RH


    B190134E01
  1. Using a moulding remover B with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.



19. REMOVE VISOR BRACKET COVER LH

HINT:
Use the same procedure as for the RH side.



20. REMOVE VISOR ASSEMBLY RH (w/o Illumination)


    B190135
  1. Remove the 3 screws and visor.



21. REMOVE VISOR ASSEMBLY LH (w/o Illumination)

HINT:
Use the same procedure as for the RH side.



22. REMOVE VISOR ASSEMBLY RH (w/ Illumination)


    B190133
  1. Remove the 4 screws.



    B191402
  1. Disconnect the connector and then remove the visor.



23. REMOVE VISOR ASSEMBLY LH (w/ Illumination)

HINT:
Use the same procedure as for the RH side.



24. REMOVE ASSIST GRIP SUB-ASSEMBLY


B190149E01

HINT:
Use the same procedure for both side.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.

  1. Disengage the 2 clips and remove the assist grip.



25. REMOVE ASSIST GRIP PLUG


    B190150E01
  1. Insert a screwdriver with its tip wrapped in protective tape, into the service notch and break off the cap.

  1. Disengage the clip and remove the assist grip plug.



26. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.



27. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B190494
  1. Disengage the 2 claws and remove the inner rear view mirror cover.



    B190495
  1. Disconnect the connector.

  1. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror.



28. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B190496
  1. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror.



29. REMOVE WINDSHIELD OUTSIDE MOULDING


B194338E01
  1. Using a knife, cut off the windshield outside moulding, as shown in the illustration.

    NOTICE:
    Do not damage the vehicle body with the knife.

  1. Remove the windshield outside moulding.

    HINT:
    Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.



30. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING


    B166393E02
  1. Using a knife, cut off the windshield outside upper moulding as shown in the illustration.

    NOTICE:
    Do not damage the vehicle body with the knife.

  1. Remove the windshield outside upper moulding.

    HINT:
    Make a partial cut in the windshield outside upper moulding. Then pull and remove it by hand.



31. REMOVE WINDSHIELD GLASS


    B191738E01
  1. Apply protective tape to the installation area on the windshield glass on the vehicle body.

    HINT:
    Apply protective tape to the installation surface to prevent it from being scratched.



    B191739E01
  1. Pass a piano wire between the vehicle body and glass from the interior.

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut off the adhesive by pulling the piano wire around the windshield glass.

    NOTICE:
    1. When separating the windshield glass, take care not to damage the paint or the interior and exterior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.



    B194333E01
  1. Place matchmarks on the windshield glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the windshield glass is not going to be reused.



  1. Disconnect the stoppers.


    B191737E01

    NOTICE:
    1. There are No. 1 and No. 2 stoppers on the windshield glass, as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
    2. To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.

    HINT:
    Depending on vehicles, a 1-piece or 2-piece type stopper is used.

  1. Using suction cups, remove the windshield glass.

    NOTICE:
    1. Be careful not to drop the windshield glass.
    2. Leave as much adhesive on the vehicle body as possible when removing the windshield glass.



32. REMOVE WINDOW GLASS ADHESIVE DAM
  1. Using a scraper, remove the adhesive dam.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the adhesive dam with a new one.



33. REMOVE NO. 2 WINDSHIELD GLASS STOPPER
  1. Using a scraper, remove the 2 No. 2 stoppers.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the No. 2 stoppers with new ones.



34. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


B194334
  1. Remove the 2 No. 1 stoppers.

    NOTICE:
    Be sure to replace the No. 1 stoppers with new ones.