Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream ON.

  6. Enter the following menus: Powertrain / Engine / Data List.

  7. According to the display on the Techstream, use the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 750 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 25%: Idling
    2. 12 to 26%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) meter/
    Min.: 0 gm/s, Max.: 655.35 gm/s
    4.0 to 8.0 g/sec.: Idling
    If the value approximately 0.0 g/sec.:
    1. Mass air flow meter power source circuit open.
    2. VG circuit open or short if the value 160.0 g/sec. or more.
    3. E2G circuit open.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature:
    Min.: -40°C, Max.: 140°C
    80 to 100°C (176 to 212°F): After warming up
    If the value -40°C (-40°F): sensor circuit open.
    If the value 140°C (284°F): sensor circuit shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If the value -40°C (-40°F): sensor circuit open.
    If the value 140°C (284°F): sensor circuit shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.5 V
    11 to 14 V: Idling
    -
    Accel Sens. No. 1 Volt %
    Absolute Accelerator Pedal Position (APP) No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: accelerator pedal is released
    54 to 86%: accelerator pedal is fully depressed
    -
    Accel Sens. No. 2 Volt %
    Absolute APP No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: accelerator pedal is released
    66 to 98%: accelerator pedal is fully depressed
    -
    Accel Sensor Out No. 1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Accel Sensor Out No. 2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Accel Sensor Out No. 1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 1.1 V: accelerator pedal is released
    2.6 to 4.5 V: accelerator pedal is fully depressed
    -
    Accel Sensor Out No. 2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.9 V
    1.2 to 2.0 V: accelerator pedal is released
    3.4 to 4.9 V: accelerator pedal is fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No. 1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Throttle Sensor Volt %
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 24%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    Read the value with intrusive operation (Active Test).
    Throttle Sensor #2 Volt %
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    -
    Calculated value based on VTA2
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    10 to 18%: Idling
    Calculated value based on VTA1
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position No. 1
    Throttle position No. 1/
    Min.: 0 V, Max.: 4.9 V
    1. 0.5 to 1.2 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully open
    -
    Throttle Position No. 2
    Throttle position No. 2/
    Min.: 0 V, Max.: 4.9 V
    1. 2.0 to 2.9 V: Throttle fully closed
    2. 4.6 to 4.9 V: Throttle fully open
    Read the value with intrusive operation (Active Test).
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.9 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.9 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No. 1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle actuator control permitted/
    ON or OFF
    ON: Idling
    Read the value with the ignition switch ON (Do not start engine).
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    -
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    -
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.92 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio/
    Min.: 0%, Max.: 100%
    0 to 40%: During idling
    When accelerator pedal depressed, duty ratio increased.
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio/
    Min.: 0%, Max.: 100%
    0 to 40%: During idling
    When accelerator pedal released quickly, duty ratio increased.
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)
    Min.: 0 V, Max.: 4.9 V
    0.4 to 0.8 V
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power inputted/
    ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage/
    Min.: 0, Max.: 19.9
    10 to 15 V: Idling
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data
    Clutch Current
    Clutch current/
    Min.: 0 A, Max.: 2.49 A
    -
    -
    Fail Safe Drive
    Whether or not fail-safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail-safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    2.0 to 4.0 ms: idling
    -
    Injection Volum (Cylinder1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.048 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    Active Test support data
    Vacuum Pump
    Key-off EVAP system pump status/
    ON or OFF
    -
    Active Test support data
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 102.3%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -50.000, Max.: 349.99
    Idling: -40 to 0%
    Service data
    Vapor Pressure Pump
    Vapor pressure/
    Min.: 33.853 kPa, Max.: 125.596 kPa
    Approximately 100 kPa: Ignition switch ON
    EVAP system pressure monitored by canister pressure sensor.
    Vapor Pressure (Calculated)
    Calculated EVAP system pressure/
    Min.: -5.632 kPa, Max.: 715.264 kPa
    Approximately 100 kPa: Ignition switch ON
    -
    EVAP System Vent Valve
    Key-off EVAP system vent valve status/
    ON or OFF
    -
    Active Test support data
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    Active Test support data
    Target Air-Fuel Ratio
    Air fuel ratio:
    Min.: 0, Max.: 1.998
    0.8 to 1.2: During idling
    -
    AF Lambda B1 S1
    Short-term fuel trim associated with the bank 1 sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2 S1
    Short-term fuel trim associated with the bank 2 sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1 S1
    Air fuel ratio sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    AFS Voltage B2 S1
    Air fuel ratio sensor output voltage for bank 2 sensor 1/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    AFS Current B1 S1
    Air fuel ratio sensor current for bank 1 sensor 1/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor.
    AFS Current B2 S1
    Air fuel ratio sensor current for bank 2 sensor 1/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor.
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2/
    Min.: 0 V, Max.: 1.27 V
    0.1 to 0.9 V:
    Driving 44 mph (70 km/h)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    O2S B2 S2
    Heated oxygen sensor output voltage for bank 2 sensor 2/
    Min.: 0 V, Max.: 1.27 V
    0.1 to 0.9 V:
    Driving 44 mph (70 km/h)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    O2S Impedance B1 S2
    Sub heated oxygen sensor impedance (bank 1 sensor 2)/
    Min.: 0 Ω, Max.: 21247.67 Ω
    5 to 15000 Ω
    After driving approx. 10 min. in urban area
    O2S Impedance B2 S2
    Sub heated oxygen sensor impedance (bank 2 sensor 2)/
    Min.: 0 Ω, Max.: 21247.67 Ω
    5 to 15000 Ω
    After driving approx. 10 min. in urban area
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio.
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value.
    Total FT #1
    Total fuel trim of bank 1
    Average value for fuel trim system of bank 1/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio.
    Long FT #2
    Long-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value.
    Total FT #2
    Total fuel trim of bank 2
    Average value for fuel trim system of bank 2/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (bank 1)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
    2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
    3. OL Drive: Open loop due to driving conditions (fuel enrichment).
    4. OL Fault: Open loop due to detected system fault.
    5. CL Fault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning.
    Fuel System Status #2
    Fuel system status (bank 2)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
    2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
    3. OL Drive: Open loop due to driving conditions (fuel enrichment).
    4. OL Fault: Open loop due to detected system fault.
    5. CL Fault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning.
    Air pump pressure (absolute)
    Air pump pressure (absolute)/
    Min.: 0 kPa, Max.: 320 kPa
    Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open
    Close to atmospheric pressure: Air pump OFF, Air switching valve close
    Refer to DTC P2431
    (Click here)
    Air Pump2 Pressure (Absolute)
    Air pump pressure (absolute)/
    Min.: 0 kPa, Max.: 320 kPa
    Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open
    Close to atmospheric pressure: Air pump OFF, Air switching valve close
    Refer to DTC P2431
    (Click here)
    Air Pump Pulsation Pressure
    Air pump pulsation pressure/
    Min.: 0 kPa, Max.: 639.98 kPa
    -
    1. Cumulative pulsation pressure calculated by ECM
    2. (Click here)
    Air Pump2 Pulsation Pressure
    Air pump pulsation pressure/
    Min.: 0 kPa, Max.: 639.98 kPa
    -
    1. Cumulative pulsation pressure calculated by ECM
    2. (Click here)
    Secondary Air Control VSV
    Secondary air injection system status
    ON or OFF
    ON: Secondary air injection system operation
    -
    2nd Air System Status
    Secondary air system status/
    ON or OFF
    ON: Secondary air system operation
    -
    AI Test
    AI operation prohibition/
    READY or NOT RDY
    READY
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 5 to 15°: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -64 CA, Max.: 1984.9 CA
    -22 to 0° CA:
    Driving, 70 km/h (44 mph)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -64 CA, Max.: 1984.9 CA
    0 to 22° CA:
    Driving, 70 km/h (44 mph)
    Service data
    ACIS VSV
    VSV status for ACIS control/
    ON or OFF
    -
    Active Test support data
    VVT Control Status #1
    Variable valve timing (VVT) control status (bank 1)/
    ON or OFF
    -
    Active Test support data
    VVT Control Status #2
    VVT control status (bank 2)/
    ON or OFF
    -
    Active Test support data
    VVT Aim Angle #1
    VVT aim angle (bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle #1
    VVT change angle (bank 1)/
    Min.: 0 DegFR, Max.: 60 DegFR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #1
    VVT OCV operation duty (bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    Requested duty value for intrusive operation
    VVT Aim Angle #2
    VVT aim angle (bank 2)/
    Min.: 0%, Max.: 100%
    0%: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle #2
    VVT change angle (bank 2)/
    Min.: 0 DegFR, Max.: 60 DegFR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #2
    VVT OCV operation duty (bank 2)/
    Min.: 0%, Max.: 100%
    0%: Idling
    Requested duty value for intrusive operation
    Catalyst Temp B1 S1
    Catalyst temperature (bank 1, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2 S1
    Catalyst temperature (bank 2, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1 S2
    Catalyst temperature (bank 1, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2 S2
    Catalyst temperature (bank 2, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Starter Control
    Starter switch status/
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal Record
    Power steering switch signal/
    ON or OFF
    ON: Power steering operation
    -
    Starter Relay
    Starter relay status/
    ON or OFF
    ON: Cranking
    -
    Power Steer. Sig. Record
    Power steering signal (history)/
    ON or OFF
    ON: When steering wheel first turned after battery terminals connected
    -
    ACC Relay
    Acc relay status/
    ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    ON: P or N position
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal is depressed
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Electrical Load Signal
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger is turned ON
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to Check Mode Procedure
    (Click here).
    AS Test Result
    Check mode result for secondary air injection system/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (bank 1)/
    Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (bank 1)/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Component Monitor ENA
    Comprehensive component monitor/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor/
    Compl or Incmpl
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor/
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor/
    Compl or Incmpl
    -
    -
    Misfire Monitor ENA
    Misfire monitor/
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor/
    Compl or Incmpl
    -
    -
    EGR/VVT Monitor ENA
    EGR/VVT monitor/
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    Heater Monitor ENA
    O2S (A/FS) heater monitor/
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor ENA
    O2S (A/FS) monitor/
    Unable or Enable
    -
    -
    O2S(A/FS) Monitor CMPL
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor ENA
    A/C monitor/
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor ENA
    2nd air monitor/
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor ENA
    EVAP monitor/
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Cat Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    # Codes (Include History)
    #Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL was ON
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs were cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs were cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    OBD Requirements
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Emission related DTCs
    -
    Number of emission related DTCs
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 800
    0 to 800
    -
    Cylinder #1 Misfire Count
    Misfire ratio of the cylinder 1/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #2 Misfire Count
    Misfire ratio of the cylinder 2/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #3 Misfire Count
    Misfire ratio of the cylinder 3/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #4 Misfire Count
    Misfire ratio of the cylinder 4/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #5 Misfire Count
    Misfire ratio of the cylinder 5/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #6 Misfire Count
    Misfire ratio of the cylinder 6/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #7 Misfire Count
    Misfire ratio of the cylinder 7/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    Cylinder #8 Misfire Count
    Misfire ratio of the cylinder 8/
    Min.: 0, Max.: 255
    0%
    This item displayed only when idling engine.
    All Cylinders Misfire Count
    All cylinders misfire rate/
    Min.: 0, Max.: 255
    0 to 35
    -
    Multi Cylinders Misfire Count
    Multiple cylinder misfire rate/
    Min.: 0 Max.: 65535
    0 to 65535
    -
    Misfire RPM
    Engine RPM for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -100%, Max.: 99.21%
    -100 to 99.2%
    Misfire detecting margin
    Power Steering Pressure
    Power steering oil pressure/
    Min.: -1.897 MPa, Max.: 12.799 MPa
    -
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operation
    The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete.
    Model Code
    Model code
    -
    Identifying the model code:
    UCK6##
    Engine Type
    Engine type
    -
    Identifying the engine type:
    2UZFE
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying the cylinder number:
    8
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    ECT (5AT)
    Destination
    Destination
    -
    Identifying the destination:
    A (America)
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying the model year:
    200#
    System Identification
    System identification
    -
    Identifying the engine system:
    Gasoline (gasoline engine)
    Engine Speed of Cyl #1
    Engine speed of cylinder 1
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #2
    Engine speed of cylinder 2
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #3
    Engine speed of cylinder 3
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #4
    Engine speed of cylinder 4
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #5
    Engine speed of cylinder 5
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #6
    Engine speed of cylinder 6
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #7
    Engine speed of cylinder 7
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Engine Speed of Cyl #8
    Engine speed of cylinder 8
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Av Engine Speed of All Cyl
    Engine speed of all cylinders
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when Check the Cylinder Compression is performed using the Active Test.
    Received MIL from ECT
    MIL status from ECT/
    ON or OFF
    ON: MIL ON
    -
    Shift Position Sig from ECT
    Shift position signal from ECT/
    1st, 2nd, 3rd, 4th or 5th
    -
    -
    A/T Oil Temp from ECT
    A/T oil temperature/
    Min.: -40°C, Max.: 215°C
    With engine cold: Equal to ambient temperature
    -
    SPD (NO)
    Output shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Vehicle stopped: 0 rpm (output shaft speed is equal to vehicle speed)
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    ECT Lock Up
    ECT lock up status/
    ON or OFF
    ON: Operating
    OFF: Not operating
    -

HINT:
*: If no conditions are specifically stated for "idling", the shift lever is in N or P, the A/C switch is OFF, and all accessory switches are OFF.


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream ON.

  6. Enter the following menus: Powertrain / Engine / Active Test

  7. According to the display on the Techstream, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12% and 25%
    1. All injectors tested at the same time.
    2. Perform test at less than 3000 rpm.
    3. Injection volume can be changed in 1% graduations within control range.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Lower by 12.5% or increase 25%
    1. Perform test at less than 3000 rpm.
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor voltage outputs.
    3. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2.
    Activate the VSV for Secondary Air Control
    Activate the Secondary Air System
    ON/OFF
    1. Do not perform test for 5 seconds or more.
    2. After test, do not perform test again for 30 seconds.
    Activate the VSV for Intake Control
    Activate VSV for intake control
    ON/OFF
    -
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    -
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    Engine is stopped.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Activate the Starter Relay
    Activate the starter relay
    ON/OFF
    Engine is stopped.
    Activate the ACC Cut Relay
    Activate the ACC CUT relay
    ON/OFF
    Engine is stopped.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. Ignition switch ON
    2. Engine does not start
    3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    4. Shift lever in P
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens fast
    Same as above.
    Control the VVT Linear (Bank1)
    Control Variable Valve Timing (VVT) [bank 1]
    -128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible during idle.
    Control the VVT System (Bank1)
    Turn on and off Oil Control Valve (OCV)
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON.
    2. Normal engine running or idling when OCV OFF.
    Control the VVT Linear (Bank2)
    Control Variable Valve Timing (VVT) [bank 2]
    -128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible during idle.
    Control the VVT System (Bank2)
    Turn on and off Oil Control Valve (OCV)
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON.
    2. Normal engine running or idling when OCV OFF.
    Activate the Vacuum Pump
    Activate vacuum pump (built into canister pump module)
    ON/OFF
    -
    Activate the VSV for Vent Valve
    Activate vent valve (built into canister pump module)
    ON/OFF
    -
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    This test is possible when the vehicle is stopped and the engine is idling.
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #7 Fuel Cut
    Cylinder #7 injector fuel cut
    ON/OFF
    Same as above.
    Control the Cylinder #8 Fuel Cut
    Cylinder #8 injector fuel cut
    ON/OFF
    Same as above.
    Control the All Cylinders Fuel Cut
    All cylinders fuel cut
    ON/OFF
    Same as above.
    Check the Cylinder Compression*
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.

    HINT:
    *: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut, and cranking occurs for approximately 10 seconds. Then, each cylinder measures the engine speed. If a cylinder engine speed is higher than the other, that cylinder compression pressure is compared to the other, and whether or not the compression pressure is low can be determined.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream ON.
    6. Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, the Active Test Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder engine speed measurement will enter standby.

    8. Fully open the throttle.
    9. Crank the engine for about 10 seconds.
    10. Monitor the engine speed (Engine Speed of Cyl #1 to #8) displayed on the Techstream.

      HINT:
      At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.
      2. If the Check the Cylinder Compression test needs to be performed after it is turned on and performed once, press Exit to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
      3. Use a fully-charged battery.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream ON.

  4. Enter the following menus: Powertrain / Engine / Utility

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Evaporative System Check
    (Automatic Mode)
    Perform 5 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. If no DTCs in Pending menu after performing this test, system functioning normally.
    2. Refer to EVAP Inspection Procedure (Click here).
    Evaporative System Check
    (Manual Mode)
    Perform 5 steps in order to operate EVAP key-off monitor manually
    35°C (95°F) or less
    1. Used to detect malfunctioning parts.
    2. Refer to EVAP Inspection Procedure (Click here).
    Air Injection Check
    (Automatic Mode)
    Perform secondary air injection system operation automatically
    With warm engine, ignition switch turned off once
    1. If no DTCs in Pending after performing this test, system functioning normally.
    2. Refer to inspection procedure for secondary air injection system DTCs.
    3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.
    4. Turn ignition switch off when System Check finished.
    Air Injection Check
    (Manual Mode)
    Perform 7 operations in order to operate air injection system monitor manually
    With warm engine, ignition switch turned off once
    1. Used to detect malfunctioning parts.
    2. Refer to inspection procedure for secondary air injection system DTCs.
    3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.
    4. Turn ignition switch off when System Check finishes.