Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0560    System Voltage

for Preparation Click here


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI NO. 1 fuse
  5. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


MONITOR STRATEGY


Related DTCs
P0560: ECM system voltage
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


ECM power source
Less than 3.5 V

WIRING DIAGRAM


A164743E08


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT FUSE (EFI NO. 1)
A162283E01
  1. Remove the EFI NO. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 1 fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (EFI NO. 1 FUSE - ECM, BATTERY)
A162284E06
  1. Check the harness and the connector between the EFI NO. 1 fuse and ECM.

    1. Remove the EFI NO. 1 fuse from the engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI NO. 1 fuse terminal 2 - A27-1 (BATT)
      Always
      Below 1 Ω
      EFI NO. 1 fuse terminal 2 or A27-1 (BATT) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and the connector between the EFI NO. 1 fuse and battery.

    1. Remove the EFI NO. 1 fuse from the engine room relay block.

    2. Disconnect the positive battery terminal.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) terminal - EFI NO. 1 fuse terminal 1
      Always
      Below 1 Ω
      Battery positive (+) terminal or EFI NO. 1 fuse terminal 1- Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT BATTERY
  1. Check that the battery is not depleted .

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


4.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR BATTERY TERMINAL
OK


5.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the Techstream off.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0560 is output
    A
    No DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)