Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the Air-Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air-fuel ratio control.
The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.
The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0420
OSC value smaller than standard value under active air-fuel ratio control
(2 trip detection logic)
  1. Gas leak from exhaust system
  2. Air-Fuel Ratio (A/F) sensor (for Bank 1 Sensor 1)
  3. Heated Oxygen (HO2) sensor (for Bank 1 Sensor 2)
  4. Front No. 2 exhaust pipe assembly (TWC)
P0430
OSC value smaller than standard value under active air-fuel ratio control
(2 trip detection logic)
  1. Gas leak from exhaust system
  2. Air-Fuel Ratio (A/F) sensor (for Bank 2 Sensor 1)
  3. Heated Oxygen (HO2) sensor (for Bank 2 Sensor 2)
  4. Front exhaust pipe assembly (TWC)

HINT:
  1. Bank 1 refers to the bank that includes No. 1 cylinder.
  2. Bank 2 refers to the bank that does not include No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR STRATEGY


Related DTCs
P0420: Catalyst Deterioration (for Bank 1)
P0430: Catalyst Deterioration (for Bank 2)
Required Sensors/Components (Main)
A/F sensor and HO2 sensor
Required Sensors/Components (Related)
Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil control valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0606, P0607 (Rear oxygen sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348, P1340 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P2440 - P2447 (Secondary air injection system)
P0500 (Vehicle speed sensor)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Front oxygen/Air fuel ratio sensor)
Battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
75°C (167°F) or more
Atmospheric pressure
76 kPa (570 mmHg) or more
Idling
OFF
Engine RPM
Less than 3200 rpm
A/F sensor status
Activated
Fuel system status
Closed loop
Engine load
10 to 75%
All of following conditions (a), (b) and (c) met
-
(a) Mass air flow rate
7.5 to 75 g/sec.
(b) Estimated front catalyst temperature
575 to 820°C (1067 to 1508°F)
(c) Estimated rear catalyst temperature
400 to 700°C (752 to 1292°F)
Rear HO2 sensor heater monitor
Completed
Transmission gear
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC)
Less than 0.12 g

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.


A164766E01

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Turn the ignition switch to ON.
  3. (c) Turn the Techstream on.
  4. (d) Clear DTCs (if set) (Click here).
  5. (e) Enter the following menus: Powertrain / Engine and ECT / Data List / All / Catalyst Monitor CMPL.
  6. (f) Check that Catalyst Monitor CMPL is incomplete.
  7. (g) Start the engine and warm it up.
  8. (h) Drive the vehicle at between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes.
  9. (i) Note the state of the Readiness Tests items. Those items will change to Complete as Catalyst Monitor CMPL monitor operates.
  10. (j) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
  11. (k) Check if any DTCs (any pending DTCs) are output.

HINT:
If Catalyst Monitor CMPL does not change to Complete, and any pending DTCs fail to set, extend the driving time.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A118003E14

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched OFF until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm and 2000 rpm at 2 second intervals, check the waveforms of the A/F and HO2 sensors using the Techstream.

HINT:
  1. If either voltage output of the Air-Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the following Control the Injection Volume for A/F Sensor using the Techstream.
  3. If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).


A121610E20


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0420 or P0430 is output
    A
    P0420 or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    Result:
    A/F sensor reacts in accordance with increases and decreases in fuel injection volume:

    +25% = Rich output:
    Less than 3.1 V

    -12.5% = Lean output:
    More than 3.4 V

    NOTICE:
    The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.


    Case
    A/F Sensor (Sensor 1) Output Voltage
    HO2 Sensor (Sensor 2) Output Voltage
    Main Suspected Trouble Area
    1
    A150787E01
    A151324E05
    A150787E01
    A150788E01
    -
    2
    A150787E01
    A150790E01
    A150787E01
    A150788E01
    1. A/F sensor
    2. A/F sensor heater
    3. A/F sensor circuit
    3
    A150787E01
    A151324E05
    A150787E01
    A150790E01
    1. HO2 sensor
    2. HO2 sensor heater
    3. HO2 sensor circuit
    4
    A150787E01
    A150790E01
    A150787E01
    A150790E01
    1. Injector
    2. Fuel pressure
    3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
    2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/ F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
    Result 
    Result
    Proceed to
    Case 1
    A
    Case 2
    B
    Case 3
    C
    Case 4
    D



B
REPLACE AIR FUEL RATIO SENSOR (Click here)

C
Go to step 4

D
CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO, REPLACE FAULTY AREA AND GO TO NEXT STEP
A


3.CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 5
A

REPAIR OR REPLACE EXHAUST GAS LEAK POINT 

4.CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK

REPLACE HEATED OXYGEN SENSOR (Click here)  

5.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
  1. According to the output DTCs in the step 1 (Check any other DTCs output), proceed to next step referring to the table below.
    Result 
    Result
    Proceed to
    P0420 is output
    A
    P0430 is output
    B
    P0420 and P0430 are output
    A and B



B
REPLACE FRONT EXHAUST PIPE ASSEMBLY (Click here)
A

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (Click here)