Home › Drivetrain · AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

A179454E07

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A27-21 (L4) - D56-81 (E1)
Y - BR
4L position signal
  1. Ignition switch ON
  2. Transfer position switch on 4L
Below 1.5 V
  1. Ignition switch ON
  2. Transfer position switch not on 4L
11 to 14 V
A27-5 (TFN) - D56-81 (E1)
G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Transfer position in neutral
Below 1.5 V
  1. Ignition switch ON
  2. Transfer position not in neutral
11 to 14 V
D56-120 (NSW) - D56-81 (E1)
L - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
D56-2 (P) - D56-81 (E1)
G-B - BR
P shift position switch signal
  1. Ignition switch ON
  2. Shift lever in P
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P
Below 1 V
D56-26 (R) - D56-81 (E1)
L-R - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
D56-25 (N) - D56-81 (E1)
G-W - BR
N shift position switch signal
  1. Ignition switch ON
  2. Shift lever in N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in N
Below 1 V
D56-27 (D) - D56-81 (E1)
G - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D
Below 1 V
A27-25 (S) - D56-81 (E1)
Y - BR
S shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in S
Below 1 V
A27-38 (SFTU) - D56-81 (E1)
G - BR
Up-shift shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever "+" position (up-shift)
Below 1 V
A27-27 (SFTD) - D56-81 (E1)
BE - BR
Down-shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever "-" position (down-shift)
Below 1 V
D56-7 (S1) - D56-81 (E1)
R - BR
S1 solenoid signal
1st gear
Below 1 V
Not on 1st gear
11 to 14 V
D56-6 (S2) - D56-81 (E1)
W - BR
S2 solenoid signal
1st, 2nd or 6th gear
11 to 14 V
3rd, 4th or 5th gear
Below 1 V
D56-3 (S3) - D56-81 (E1)
G-W - BR
S3 solenoid signal
1st, 2nd or 3rd gear
11 to 14 V
4th, 5th or 6th gear
Below 1 V
D56-5 (S4) - D56-81 (E1)
G-R - BR
S4 solenoid signal
5th or 6th gear
11 to 14 V
1st, 2nd, 3rd or 4th gear
Below 1 V
D56-4 (SR) - D56-81 (E1)
G - BR
SR solenoid signal
1st, 2nd, 3rd or 4th gear
11 to 14 V
5th or 6th gear
Below 1 V
D56-14 (SL1+) - D56-15 (SL1-)
Y - L
SL1 solenoid signal
5th or 6th gear
Pulse generation
(see waveform 1)
D56-12 (SL2+) - D56-13 (SL2-)
G-R - L-W
SL2 solenoid signal
Engine is idling
Pulse generation
(see waveform 2)
D56-9 (SLT+) - D56-8 (SLT-)
B - G-B
SLT solenoid signal
Engine is idling
Pulse generation
(see waveform 3)
D56-10 (SLU+) - D56-11 (SLU-)
L-Y - L-R
SLU solenoid signal
5th (lock-up) gear or 6th (lock-up) gear
Pulse generation
(see waveform 4)
D56-122 (THO1) - D56-98 (ETHA)
G-Y - BR
No. 1 ATF temperature sensor signal
No. 1 ATF temperature: 115°C (239°F) or more
Below 1.5 V
D56-99 (THO2) - D56-98 (ETHA)
L - BR
No. 2 ATF temperature sensor signal
No. 2 ATF temperature: 115°C (239°F) or more
Below 1.5 V
D56-101 (SP2+) - D56-100 (SP2-)
Y - B
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(see waveform 5)
D56-124 (NT+) - D56-123 (NT-)
Y - B
Speed sensor NT signal
Engine is idling
(shift lever in P or N)
Pulse generation
(see waveform 6)
A27-10 (CANH) - D56-81 (E1)
GR - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 7)
A27-11 (CANL) - D56-81 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 8)
A27-51 (PWR) - D56-81 (E1)
L - BR
Tow/haul pattern select switch signal
  1. Ignition switch ON
  2. Tow/haul pattern select switch ON
0 to 1.5 V
  1. Ignition switch ON
  2. Tow/haul pattern select switch OFF
Pulse generation*


    C140833E07
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-14 (SL1+) - D56-15 (SL1-)
    Tool setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



  2. C140833E08
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-12 (SL2+) - D56-13 (SL2-)
    Tool setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



  4. C140833E09
  5. Using an oscilloscope, check waveform 3.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-9 (SLT+) - D56-8 (SLT-)
    Tool setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



  6. C162560E02
  7. Using an oscilloscope, check waveform 4.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-10 (SLU+) - D56-11 (SLU-)
    Tool setting
    5 V/DIV., 1 msec./DIV.
    Condition
    5th (lock-up)



  8. C161208E04
  9. Using an oscilloscope, check waveform 5.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-101 (SP2+) - D56-100 (SP2-)
    Tool setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Vehicle speed 20 km/h (12 mph)



  10. C162170E03
  11. Using an oscilloscope, check waveform 6.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    D56-124 (NT+) - D56-123 (NT-)
    Tool setting
    1 V/DIV., 2 msec./DIV.
    Condition
    Engine is idling (Shift lever in P or N)



  12. C161206E03
  13. Using an oscilloscope, check waveform 7.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    A27-10 (CANH) - D56-81 (E1)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON



  14. C161207E03
  15. Using an oscilloscope, check waveform 8.
    Reference 
    Item
    Content
    Terminal No. (Symbol)
    A27-11 (CANL) - D56-81 (E1)
    Tool setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON