DTC P0761 Shift Solenoid "C" Performance (Shift Solenoid Valve S3) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0761 |
(b) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips). |
|
| P0761 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 6th. |
|
| ECM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under S3 stuck ON malfunction | 1st | 2nd | 3rd | 3rd | N* | N* |
| *2: Actual gear position under S3 stuck OFF malfunction | 3rd | 4th | 4th | 4th | 5th | 6th |
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under fail-safe mode when S3 stuck ON malfunction | 1st | 2nd | 3rd | 3rd | 3rd | 3rd |
| *2: Actual gear position under fail-safe mode when S3 stuck OFF malfunction | 3rd | 4th | 4th | 4th | 5th | 6th |
| Related DTCs | P0761: Shift solenoid valve S3/OFF malfunction Shift solenoid valve S3/ON malfunction |
| Required sensors/Components | Shift solenoid valve S3 |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A), (B) and ON malfunction (A) 0.4 seconds ON malfunction (B) 3 seconds ON malfunction (C) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve S3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Transfer position | HIGH* |
| Vehicle speed sensor circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| Transfer input speed/Transfer output speed (NO/NOtf) | 0.9 or more, and less than 1.1 |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed (NT/NO) | 0.93 or more, and 1.07 or less (This means actual gear is 4th) |
| Turbine speed/Output speed (NT/NO) | 0.51 or more, and 0.65 or less (This means actual gear is 6th) |
| Turbine speed/Output speed (NT/NO) | 1.24 or more, and 1.49 or less (This means actual gear is 3rd) |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1000 rpm or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position by yourself |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| ECM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S3 | ON | ON | ON | OFF | OFF | OFF |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0761) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0761 is output | A |
| P0761 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE S3 |
![]() |
Remove the shift solenoid valve S3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly.
|
| ||||
| OK | ||
| ||