DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |
DTC P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
DTC P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 P2197 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage more than 3.8 V for 5 seconds (b) Heated Oxygen (HO2) sensor voltage rises from less than 0.21 V to 0.59 V or more |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 3.6 mA or more for 3 seconds (2 trip detection logic) |
| |
| P2196 P2198 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage less than 2.8 V for 5 seconds (b) HO2 sensor voltage falls from 0.59 V or more to less than 0.21 V |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 1.4 mA for 3 seconds (2 trip detection logic) |
|

| Related DTCs | P2195: A/F sensor signal stuck lean (Bank 1) P2196: A/F sensor signal stuck rich (Bank 1) P2197: A/F sensor signal stuck lean (Bank 2) P2198: A/F sensor signal stuck rich (Bank 2) |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | HO2 sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: Sensor voltage detection monitor 3 seconds: Sensor current detection monitor |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P1340 (Camshaft position sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P0451, P0452, P0453, P1451, P1452, P1453, P1455 (EVAP system) P2440 - P2447 (Secondary air injection system) P0500 (Vehicle speed sensor) P0505 (IAC valve) |
| Time after engine start | 30 seconds or more |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| A/F sensor status | Activated |
| Continuous time of fuel cut | 3 to 10 seconds |
| ECT | 75°C (167°F) or more |
| Rear HO2S voltage | Rises from less than 0.21 V to 0.59 V or more |
| A/F sensor voltage | More than 3.8 V for 5 seconds |
| Rear HO2S voltage | Falls from 0.59 V or more to less than 0.21 V |
| A/F sensor voltage | Less than 2.8 V for 5 seconds |
| A/F sensor current | 3.6 mA or more |
| A/F sensor current | Less than 1.4 mA |


| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (A/F) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.4 V | |
| O2S B1S2 (HO2) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V | |
| AFS Voltage B2S1 (A/F) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.4 V | |
| O2S B2S2 (HO2) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2195, P2196, P2197 or P2198 is output | A |
| P2195, P2196, P2197 or P2198 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Allow the vehicle to drive in accordance with the drive pattern described in the CONFIRMATION DRIVING PATTERN.
Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor.
Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RANGE B1 S1.
Check the test value of the A/F sensor output current during fuel-cut.
| Test Value | Proceed to |
| Within normal range (1.4 mA or more, and less than 3.6 mA) | A |
| Outside normal range (Less than 1.4 mA, or 3.6 mA or more) | B |
|
| ||||
| A | |
| 3.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the A/F sensor at an engine speed of 2500 rpm for 90 seconds.
On the Techstream, enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Snapshot / AFS Voltage B1S1 or AFS Voltage B2S1 and Engine Speed.
Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:
| Condition | A/F Sensor Voltage Variation | Reference |
| (1) and (2) | Remains at approximately 3.3 V | 3.1 V to 3.5 V |
| (3) | Increases to 3.8 V or more | This occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| P2195, P2196, P2197 or P2198 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2195, P2196, P2197 or P2198 is output | B |
|
| ||||
| A | ||
| ||
| 9.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA1A) - 4 (A1A-) | Always | 10 kΩ or higher |
| 1 (HA2A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA2A) - 4 (A2A-) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT INTEGRATION RELAY (A/F) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the A/F fuse.
Remove the A/F fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A/F fuse | Always | Below 1 Ω |
Reinstall the A/F fuse.
Inspect the integration relay (A/F).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1A-4 | When no battery voltage applied to terminals 1A-2 and 1A-3 | 10 kΩ or higher |
| When battery voltage applied to terminals 1A-2 and 1A-3 | Below 1 Ω |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D19-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D20-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D19-1 (HA1A) - D56-22 (HA1A) | Always | Below 1 Ω |
| D19-3 (A1A+) - D56-126 (A1A+) | Always | Below 1 Ω |
| D19-4 (A1A-) - D56-125 (A1A-) | Always | Below 1 Ω |
| D20-1 (HA2A) - D56-20 (HA2A) | Always | Below 1 Ω |
| D20-3 (A2A+) - D56-103 (A2A+) | Always | Below 1 Ω |
| D20-4 (A2A-) - D56-102 (A2A-) | Always | Below 1 Ω |
| D19-1 (HA1A) or D56-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D19-3 (A1A+) or D56-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D19-4 (A1A-) or D56-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D20-1 (HA2A) or D56-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D20-3 (A2A+) or D56-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D20-4 (A2A-) or D56-102 (A2A-) - Body ground | Always | 10 kΩ or higher |

|
| ||||
| OK | |
| 12.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the Techstream.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2195, P2196, P2197 or P2198 is output | B |
|
| ||||
| A | ||
| ||