POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BATTERY) |
![]() |
Disconnect the N9 rear power window regulator switch assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N9-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the rear power window regulator switch assembly LH connector.
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
![]() |
Remove the rear power window regulator switch assembly LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (U) - 3 (B) | UP | Below 1 Ω |
| 1 (D) - 2 (SD) | UP | Below 1 Ω |
| 4 (U) - 5 (SU) | OFF | Below 1 Ω |
| 1 (D) - 2 (SD) | OFF | Below 1 Ω |
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) | DOWN | Below 1 Ω |
Reinstall the rear power window regulator switch assembly LH.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW SWITCH LH - REAR POWER WINDOW MOTOR LH) |
![]() |
Disconnect the N9 rear power window regulator switch assembly LH connector.
Disconnect the N10 rear power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N9-1 (D) - N10-1 | Always | Below 1 Ω |
| N9-4 (U) - N10-2 | Always | Below 1 Ω |
| N9-1 (D) - Body ground | Always | 10 kΩ or higher |
| N9-4 (U) - Body ground | Always | 10 kΩ or higher |
Reconnect the rear power window regulator motor assembly LH connector.
Reconnect the rear power window regulator switch assembly LH connector.
|
| ||||
| OK | |
| 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Remove the rear power window regulator motor assembly LH (Click here).
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates counterclockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates clockwise |
Reinstall the rear power window regulator motor assembly LH.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - REAR POWER WINDOW SWITCH LH) |
![]() |
Disconnect the M2 power window regulator master switch assembly connector.
Disconnect the N9 rear power window regulator switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M2-12 (U) - N9-5 (SU) | Always | Below 1 Ω |
| M2-15 (D) - N9-2 (SD) | Always | Below 1 Ω |
| M2-12 (U) - Body ground | Always | 10 kΩ or higher |
| M2-15 (D) - Body ground | Always | 10 kΩ or higher |
Reconnect the rear power window regulator switch assembly LH connector.
Reconnect the power window regulator master switch assembly connector.
|
| ||||
| OK | ||
| ||