Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MULTIPLEX TILT AND TELESCOPIC ECU

F044288E14

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-2 (TEM+) - H57-11 (GND)
    (Not available) - W-B
    Telescopic motor output
    1. Ignition switch ON
    2. Telescopic steering contracts
    11 to 14 V
    Telescopic motor is not operating
    Below 1 V
    A-3 (VCE) - A-5 (E2)
    (Not available)
    Telescopic sensor power source
    Ignition switch ON
    8 to 16 V
    A-4 (TES) - A-5 (E2)
    (Not available)
    Telescopic sensor signal
    Telescopic motor is operating
    Pulse generation
    HI: 8 to 16 V
    LOW: 0 V
    A-5 (E2) - Body ground
    (Not available) - Body ground
    Telescopic sensor ground
    Always
    Below 1 V
    A-6 (TEM-) - H57-11 (GND)
    (Not available) - W-B
    Telescopic motor output
    1. Ignition switch ON
    2. Telescopic steering extends
    11 to 14 V
    Telescopic motor is not operating
    Below 1 V
    H57-1 (TIM-) - H57-11 (GND)
    R - W-B
    Tilt motor output
    1. Ignition switch ON
    2. Steering tilts down
    11 to 14 V
    Tilt motor is not operating
    Below 1 V
    H57-2 (+B) - H57-11 (GND)
    V - W-B
    Motor power source
    Always
    11 to 14 V
    H57-3 (MSW) - H57-11 (GND)
    GR - W-B
    Manual switch signal
    1. Ignition switch ON
    2. Tilt up by manual switch
    1.67 to 2.13 V
    1. Ignition switch ON
    2. Tilt down by manual switch
    0.54 to 0.74 V
    1. Ignition switch ON
    2. Telescopic contracted by manual switch
    1.08 to 1.40 V
    1. Ignition switch ON
    2. Telescopic extended by manual switch
    2.22 to 2.77 V
    Manual switch is not operating
    Below 0.2 V
    H57-4 (VC) - H57-11 (GND)
    Y - W-B
    Manual switch power source
    Ignition switch ON
    4.9 to 5.1 V
    H57-5 (CANH) - H57-11 (GND)
    O - W-B
    CAN communication
    Ignition switch ON
    Pulse generation
    H57-6 (VCI) - H57-17 (E1)
    SB - LG
    Tilt sensor power source
    Ignition switch ON
    8 to 16 V
    H57-7 (TIS) - H57-17 (E1)
    G - LG
    Tilt sensor signal
    Tilt motor is operating
    Pulse generation
    HI: 8 to 16 V
    LOW: 0 V
    H57-8 (IG) - H57-11 (GND)
    P - W-B
    IG signal/IG power source
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    H57-9 (ECUB) - H57-11 (GND)
    L - W-B
    ECU power source
    Always
    11 to 14 V
    H57-10 (TIM+) - H57-11 (GND)
    B - W-B
    Tilt motor output
    1. Ignition switch ON
    2. Steering tilts up
    11 to 14 V
    Tilt motor is not operating
    Below 1 V
    H57-11 (GND) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 V
    H57-14 (CANL) - H57-11 (GND)
    W - W-B
    CAN communication
    Ignition switch ON
    Pulse generation
    H57-17 (E1) - Body ground
    LG - Body ground
    Tilt sensor ground
    Always
    Below 1 V