POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical/ Tilt & Telescopic / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Tilt Position | Current tilt position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Position | Current telescopic position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Return Position | Memorized tilt return position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Return Position | Memorized telescopic return position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Memory Pos 1 | Tilt data of memory position 1 / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Memory Pos 1 | Telescopic data of memory position 1 / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Memory Pos 2 | Tilt data of memory position 2 / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Memory Pos 2 | Telescopic data of memory position 2 / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Up Limit | Uppermost tilt position / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| Tilt Up Limit Position | Uppermost tilt position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Down Limit | Lowermost tilt position / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| Tilt Down Limit Position | Lowermost tilt position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Short Limit | Shortest telescopic position / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| Telesco Short Limit Pos | Shortest telescopic position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Telesco Long Limit | Longest telescopic position / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| Telesco Long Limit Pos | Longest telescopic position data / min.: 0, max.: 65535 | 28672 to 36864 | - |
| Tilt Up Switch | Input state of tilt up by manual switch / ON or OFF | ON: Tilt up is activated by manual switch OFF: Tilt up is not activated by manual switch | - |
| Tilt Down Switch | Input state of tilt down by manual switch / ON or OFF | ON: Tilt down is activated by manual switch OFF: Tilt down is not activated by manual switch | - |
| Telesco Short Switch | Input state of telescopic short by manual switch / ON or OFF | ON: Telescopic short is activated by manual switch OFF: Telescopic short is not activated by manual switch | - |
| Telesco Long Switch | Input state of telescopic long by manual switch / ON or OFF | ON: Telescopic long is activated by manual switch OFF: Telescopic long is not activated by manual switch | - |
| T&T Manual SW Data | Voltage data of manual switch / min.: 0 V, max.: 5 V | Neutral position: Below 0.2 V Tilt up: 1.67 to 2.13 V Tilt down: 0.54 to 0.74 V Telescopic contract: 1.08 to 1.40 V Telescopic extend: 2.22 to 2.77 V | - |
| S/B Mem 1 | Tilt and telescopic memory position 1 / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| S/B Mem 2 | Tilt and telescopic memory position 2 / Not Mem or Mem | Not Mem: Position is not memorized Mem: Position is memorized | - |
| T&T Autoaway Function | Auto away and return function / ON or OFF | ON: Auto away and return function is allowed OFF: Auto away and return function is prohibited | - |
| Power Source Voltage | Voltage data of power supply / min.: 0 V, max.: 20 V | Actual power supply voltage 11 to 14 V | - |
| Freeze Speed Info | Vehicle speed data / min: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| IG Switch (CAN) | Communication state of power switch / ON or OFF | ON: Communication is normal OFF: Communication is interrupted | - |
| IG Switch | Input state of power switch / ON or OFF | ON: Input signal is normal OFF: Input signal is interrupted | - |
| Key Switch (CAN) | Communication state of key switch signal / ON or OFF | ON: Communication is normal OFF: Communication is interrupted | - |
| Key Code Confirm (CAN) | Communication state of key code confirmation signal / ON or OFF | ON: Communication is normal OFF: Communication is interrupted | - |
| Receive from Meter | Communication state of combination meter signal / OK or Interpt | OK: Communication is normal Interpt: Communication is interrupted | - |
| Receive from Seat ECU | Communication state of front power seat control switch LH signal / OK or Interpt | OK: Communication is normal Interpt: Communication is interrupted | - |
| J/B | Communication state of main body ECU signal / OK or Interpt | OK: Communication is normal Interpt: Communication is interrupted | - |
| B/B | Communication state of optional after parts ECU signal / OK or Interpt | OK: Communication is normal Interpt: Communication is interrupted | - |
| The Number of DTCs | Number of diagnosis codes / min.: 0, max.: 255 | Actual number of diagnosis codes | - |
| PERFORM ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
Check the values by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Tilt Operation | Tilt operation | UP/DOWN | - |
| Telesco Operation | Telescopic operation | SHORT/LONG | - |