Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the illumination circuit for the navigation receiver and steering pad switch assembly when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E138076E02


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read Precaution for the supplemental restraint system (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box light or other parts (seat heater switch, room light switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver.
    B
    No illumination (navigation receiver, glove box light, room light switch, etc.) comes on.
    C
    Illumination comes on for all components except steering pad switch and navigation receiver.
    D



B
Go to step 5

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER - BATTERY AND BODY GROUND)


    E138073E04
  1. Disconnect the H54 spiral cable connector.

  1. Disconnect the I24 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-4 (EAU) - I24-6 (SWG)
    Always
    Below 1 Ω
    H54-4 (EAU) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H54-12 (IL+2) - Body ground
    Light control switch OFF
    Below 1 V
    Light control switch TAIL or HEAD
    11 to 14 V

  1. Reconnect the spiral cable connector.

  1. Reconnect the navigation receiver assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E138075E02

  1. Disconnect the z12 steering pad switch assembly connector.

  1. Connect the positive (+) lead to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

  1. Reconnect the steering pad switch assembly connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE


    C152441E09
  1. Disconnect the z12 and H54 spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z12-5 (IL+2) - H54-12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z12-8 (EAU) - H54-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read Precaution for the supplemental restraint system (Click here).

  1. Reconnect the spiral cable connectors.



NG
REPLACE SPIRAL CABLE (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY AND BODY GROUND)


    E138077E03
  1. Disconnect the I20 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I20-2 (ILL+) - Body ground
    Light control switch
    TAIL or HEAD
    11 to 14 V
    Light control switch OFF
    Below 1 Ω

  1. Reconnect the navigation receiver assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION METER)


    E138078E02
  1. Disconnect the I20 navigation receiver assembly connector.

  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I20-12 (ILL-) - H37-37 (ILL-)
    Always
    Below 1 Ω
    I20-12 (ILL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the navigation receiver assembly connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)