Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the navigation system cannot be operated using the steering pad switch assembly, and the navigation system itself cannot function.

WIRING DIAGRAM


E146424E03


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read Precaution for the supplemental restraint system (Click here).

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - SPIRAL CABLE)


    E138073E03
  1. Disconnect the I24 navigation receiver assembly connector.

  1. Disconnect the H54 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-8 (SW2) - H54-5 (AU2)
    Always
    Below 1 Ω
    I24-6 (SWG) - H54-4 (EAU)
    I24-7 (SW1) - H54-6 (AU1)
    I24-8 (SW2) - Body ground
    Always
    10 kΩ or higher
    I24-6 (SWG) - Body ground
    I24-7 (SW1) - Body ground

  1. Reconnect the spiral cable connector.

  1. Reconnect the navigation receiver assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SPIRAL CABLE


    C152441E08
  1. Disconnect the z12 and H54 spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-4 (EAU) - z12-8 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    H54-5 (AU2) - z12-9 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    H54-6 (AU1) - z12-10 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read Precaution for the supplemental restraint system (Click here).

  1. Reconnect the spiral cable connectors.



NG
REPLACE SPIRAL CABLE (Click here)
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E138074E02

  1. Disconnect the z12 steering pad switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    MODE switch pushed
    Below 1 Ω
    On Hook switch pushed
    312 to 345 Ω
    Off Hook switch pushed
    950 to 1050 Ω
    Voice switch is pushed
    2954 to 3265 Ω
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch pushed
    Below 1 Ω
    Seek- switch pushed
    312 to 345 Ω
    Volume+ switch is pushed
    950 to 1050 Ω
    Volume- switch is pushed
    2954 to 3265 Ω

  1. Reconnect the steering pad switch assembly connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)