Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E160658E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch*.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on (radio receiver, hazard switch, glove box, etc.).
    C
    Illumination comes on for all components except steering pad switch* and radio receiver.
    D

    HINT:
    *: for 8 Speakers, there is no steering pad switch.



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY AND BODY GROUND)


    E121218E12
  1. Disconnect the H54 spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H54-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V

  1. Reconnect the spiral cable connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E138075E02

  1. Disconnect the z12 steering pad switch assembly connector.

  1. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

  1. Reconnect the steering pad switch assembly connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE


    C152441E09
  1. Disconnect the z12 steering pad switch assembly connector.

  1. Disconnect the H54 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z12-8 (EAU) - H54-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z12-5 (IL+2) - H54-12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read Precaution for the SRS (Click here).

  1. Reconnect the steering pad switch assembly connector.

  1. Reconnect the spiral cable connector.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER ASSEMBLY)


    E145920E04
  1. Disconnect the I3 radio receiver assembly connector.

  1. Disconnect the H54 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-6 (SWG) - H54-4 (EAU)
    Always
    Below 1 Ω
    I3-6 (SWG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the spiral cable connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)


    E145921E02
  1. Disconnect the I1*1 or I4*2 radio receiver assembly connector.

    HINT:
    *1: for 8 Speakers
    *2: for 14 Speakers

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 8 Speakers 
    Tester Connection
    Switch Condition
    Specified Condition
    I1-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V
    for 14 Speakers 
    Tester Connection
    Switch Condition
    Specified Condition
    I4-2 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V

  1. Reconnect the radio receiver assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMBINATION METER)


    E145922E02
  1. Disconnect the I2*1 or I4*2 radio receiver assembly connector.

    HINT:
    *1: for 8 Speakers
    *2: for 14 Speakers

  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 8 Speakers 
    Tester Connection
    Condition
    Specified Condition
    I2-5 (ILL-) - H37-37 (ILL-)
    Always
    Below 1 Ω
    I2-5 (ILL-) - Body ground
    Always
    10 kΩ or higher
    for 14 Speakers 
    Tester Connection
    Condition
    Specified Condition
    I4-12 (ILL-) - H37-37 (ILL-)
    Always
    Below 1 Ω
    I4-12 (ILL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)