Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM


E146424E02


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.INSPECT RADIO RECEIVER ASSEMBLY


    B109191E05
  1. Disconnect the I3 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I3-7 (SW1) - I3-6 (SWG)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch: push
    Below 1 Ω
    Seek- switch: push
    312 to 345 Ω
    Volume+ switch: push
    950 to 1050 Ω
    Volume- switch: push
    2954 to 3265 Ω
    I3-8 (SW2) - I3-6 (SWG)
    No switch is pushed
    100 kΩ or higher
    MODE switch: push
    Below 1 Ω
    On Hook switch: push
    312 to 345 Ω
    Off Hook switch: push
    950 to 1050 Ω

  1. Reconnect the radio receiver assembly connector.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY

E138074E02

  1. Disconnect the z12 steering pad switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch: push
    Below 1 Ω
    Seek- switch: push
    312 to 345 Ω
    Volume+ switch: push
    950 to 1050 Ω
    Volume- switch: push
    2954 to 3265 Ω
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    MODE switch: push
    Below 1 Ω
    On Hook switch: push
    312 to 345 Ω
    Off Hook switch: push
    950 to 1050 Ω

  1. Reconnect the steering pad switch assembly connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE


    C152441E08
  1. Disconnect the z12 steering pad switch assembly connector.

  1. Disconnect the H54 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z12-8 (EAU) - H54-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z12-10 (AU1) - H54-6 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z12-9 (AU2) - H54-5 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the PRECAUTION for the SRS (Click here).

  1. Reconnect the steering pad switch assembly connector.

  1. Reconnect the spiral cable connector.



NG
REPLACE SPIRAL CABLE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)