Home › Brake › BRAKE (FRONT) › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DISC


    C155464E01
  1. Align the matchmarks, and then install the front disc.

    HINT:
    When replacing the front disc with a new one, select the installation position where the front disc has the smallest runout.



2. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C154478
  1. Install the disc brake caliper with 2 new bolts.

    Torque:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }



3. CONNECT NO. 7 FRONT BRAKE TUBE


    C155482E03
  1. Using a union nut wrench (10 mm), connect the front brake tube.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



4. INSTALL FRONT DISC BRAKE PAD KIT


    C155459E02
  1. Apply disc brake grease to both sides of the No. 1 anti-squeal shims.

  1. Install the No. 1 and No. 2 anti-squeal shims to each pad.



    C155460
  1. Install the 2 pads to the disc brake caliper.



    C155461
  1. Install the front disc brake anti-rattle spring between the 2 pads.

    NOTICE:
    The anti-rattle spring can be used again if it has sufficient rebound; no deformation, cracks or wear; and has had all rust, dirt and foreign matter cleaned off.



    C154476
  1. Install the 2 hole pins.

  1. Install the pin hold clip.

    NOTICE:
    The pin hold clip can be used again if it has sufficient rebound; no deformation or wear; and has had all rust, dirt and foreign matter cleaned off.



5. FILL RESERVOIR WITH BRAKE FLUID


    C155472
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    NOTICE:
    1. Make sure there is sufficient brake fluid in the can.
    2. After adding brake fluid, make sure the reservoir is sufficiently full.



6. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.



    C155473E04
  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

  1. Slowly depress and hold the brake pedal.



    C155474
  1. Block the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. This torque value is effective when union nut wrench is parallel to the torque wrench.



7. BLEED AIR FROM BRAKE LINE



C155475E01

  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



8. BLEED AIR FROM VSC ACTUATOR ASSEMBLY

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the Techstream to the DLC3, and turn the ignition switch ON.

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.

  1. Bleed the air out of the suction line.

    NOTICE:
    1. Perform the bleeding at the right front wheel and right rear wheel.
    2. Bleed the air by following the steps displayed on the Techstream.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.

    2. Loosen the bleeder plug.

    3. Operate the brake actuator to bleed the air using the Techstream.

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    4. Check if the operation has stopped by referring to the Techstream display.

    5. Temporarily tighten the bleeder plug.

    6. Repeat the 4 previous steps until all air in the fluid is completely bled out.

    7. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    8. Repeat all of the above procedures for the other wheel to bleed the air out of the suction line.

  1. Bleed the air out of the pressure reduction line.

    NOTICE:
    1. Perform the bleeding at the 4 wheels.
    2. Bleed the air by following the steps displayed on the Techstream.


    1. Connect a vinyl tube to one of the bleeder plugs.

    2. Loosen the bleeder plug.

    3. Using the Techstream, operate the brake actuator, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Depress and hold the brake pedal. Do not depress and release the pedal repeatedly.

      HINT:
      The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.

    4. Tighten the bleeder plug, and then release the brake pedal.

    5. Repeat the 3 previous steps until all air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    7. Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.



9. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    C155477
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



10. INSPECT FOR BRAKE FLUID LEAK


11. INSTALL FRONT WHEEL
  1. for Aluminum Wheel

Torque:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }

  1. for Steel Wheel

Torque:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }