AUTOMATIC TRANSMISSION UNIT > INSPECTION |
| 1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
![]() |
Remove the magnets, and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
| 2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the reverse clutch hub and turn the 1-way clutch assembly.
Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
| 3. INSPECT REAR CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 4. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.
| 5. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the forward clutch hub bush.
| 6. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 7. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 8. INSPECT DIRECT CLUTCH DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 9. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 10. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 11. INSPECT NO. 3 BRAKE DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 12. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 13. INSPECT FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the front planetary pinion gear thrust clearance.
![]() |
Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.
| 14. INSPECT 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the 1-way clutch to the 1-way clutch inner race.
Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
Remove the 1-way clutch from the 1-way clutch inner race.
| 15. INSPECT NO. 1 BRAKE DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 16. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 17. INSPECT NO. 2 BRAKE DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 18. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 19. INSPECT CENTER PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the center planetary gear pinion thrust clearance.
| 20. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
| 21. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.
| 22. INSPECT INTERMEDIATE SHAFT |
![]() |
Using a dial indicator, measure the intermediate shaft runout.
![]() |
Using a micrometer, check the outer diameter of the intermediate shaft positions shown in the diagram.
| Bolt | Bolt Length |
| A, B | 25.962 to 25.975 mm (1.022 to 1.023 in.) |
| C, D | 32.062 to 32.075 mm (1.262 to 1.263 in.) |
| Bolt | Bolt Length |
| A, B | 25.912 mm (1.02 in.) |
| C, D | 32.012 mm (1.26 in.) |
| 23. INSPECT NO. 4 BRAKE DISC |
![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
| 24. INSPECT REAR PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary gear bush.
| 25. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 26. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE |
![]() |
Make sure the 1st and reverse brake piston moves smoothly when applying and releasing the compressed air into the transmission case.
| 27. INSPECT PISTON STROKE OF NO. 1 BRAKE PISTON |
![]() |
Make sure the No. 1 brake piston moves smoothly when applying and releasing the compressed air into the transmission case.
![]() |
Using a feeler gauge, measure the B3 bearing pack clearance between the snap ring and flange.
| 28. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() |
Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
| No. | Thickness | No. | Thickness |
| 0 | 3.0 mm (0.118 in.) | 5 | 3.5 mm (0.138 in.) |
| 1 | 3.1 mm (0.122 in.) | 6 | 3.6 mm (0.142 in.) |
| 2 | 3.2 mm (0.126 in.) | 7 | 3.7 mm (0.146 in.) |
| 3 | 3.3 mm (0.130 in.) | 8 | 3.8 mm (0.150 in.) |
| 4 | 3.4 mm (0.134 in.) | - | - |
| 29. INSPECT PACK CLEARANCE OF REVERSE CLUTCH |
Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse flange at the both ends across a diameter while blowing air (392 kPa, 4.0 kgf/cm2, 57 psi) from the oil hole as shown in the illustration, and calculate the average.

| No. | Thickness | No. | Thickness |
| 0 | 2.8 mm (0.110 in.) | 6 | 3.4 mm (0.134 in.) |
| 1 | 2.9 mm (0.114 in.) | 7 | 3.5 mm (0.138 in.) |
| 2 | 3.0 mm (0.118 in.) | 8 | 3.6 mm (0.142 in.) |
| 3 | 3.1 mm (0.122 in.) | 9 | 3.7 mm (0.146 in.) |
| 4 | 3.2 mm (0.126 in.) | A | 3.8 mm (0.150 in.) |
| 5 | 3.3 mm (0.130 in.) | - | - |
| 30. INSPECT PACK CLEARANCE OF FORWARD CLUTCH |
![]() |
Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
| No. | Thickness | No. | Thickness |
| 0 | 3.0 mm (0.118 in.) | 6 | 3.6 mm (0.142 in.) |
| 1 | 3.1 mm (0.122 in.) | 7 | 3.7 mm (0.146 in.) |
| 2 | 3.2 mm (0.126 in.) | 8 | 3.8 mm (0.150 in.) |
| 3 | 3.3 mm (0.130 in.) | 9 | 3.9 mm (0.154 in.) |
| 4 | 3.4 mm (0.134 in.) | A | 4.0 mm (0.158 in.) |
| 5 | 3.5 mm (0.138 in.) | - | - |
| 31. INSPECT INDIVIDUAL PISTON OPERATION |
![]() |
Check the operating sound while applying compressed air into the oil holes indicated in the illustration.