Home › Drivetrain ยท AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH


    C159655
  1. Remove the nut, spring washer and control shaft lever.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C159656
  1. Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut, lock washer and bolt.

  1. Remove the park/neutral position switch.



3. REMOVE SPEED SENSOR


    C159658
  1. Remove the 2 bolts and 2 speed sensors.

  1. Remove the 2 O-rings from the sensors.



4. REMOVE TRANSMISSION OIL COOLER ASSEMBLY


    C161366
  1. w/ Trailer Towing System:

    1. Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.

    2. Separate the transmission oil cooler from the transmission oil thermostat.

    3. Remove the 4 O-rings.



    C161367
  1. w/o Trailer Towing System:

    1. Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.

    2. Separate the transmission oil cooler from the transmission oil cooler spacer.

    3. Remove the 4 O-rings.



5. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE


    C178810
  1. Remove the 2 bolts.

  1. Remove the breather tube.

  1. Remove the O-ring from the tube.



6. REMOVE AUTOMATIC TRANSMISSION HOUSING


    C159660
  1. Remove the 14 bolts.

  1. Remove the transmission housing.



7. REMOVE EXTENSION HOUSING SUB-ASSEMBLY


    C161608
  1. Remove the 10 bolts.



    C161609
  1. Remove the extension housing.

    HINT:
    Tap on the circumference of the extension housing with a plastic-faced hammer to remove the extension housing.



8. REMOVE EXTENSION HOUSING REAR OIL SEAL


    C161612E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



9. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


    C161613
  1. Install the transmission case on the overhaul attachment.



10. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    C178808E02
  1. Remove the drain plug, 12 bolts, oil pan and gasket.

    NOTICE:
    Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.



11. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    D001124E01
  1. Remove the magnets, and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bush wear



12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C178807
  1. Turn over the transmission.

  1. Remove the 4 bolts and oil strainer from the valve body.

  1. Remove the O-ring from the oil strainer.



13. REMOVE TRANSMISSION WIRE


    C161112E01
  1. Remove the 2 bolts and 2 temperature sensor clamps.

  1. Disconnect the 2 ATF temperature sensors.

  1. Disconnect the 9 connectors from the solenoid valves.



    C161614
  1. Remove the 2 bolts and pull out the No. 1 and No. 2 transmission wires.

  1. Pull the transmission wires out of the transmission case.



    C161615
  1. Remove the 2 O-rings from the transmission wires.



14. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C162147E02
  1. Remove the bolt, detent spring cover and detent spring.

  1. Remove the 19 bolts.

  1. Remove the valve body assembly.



15. REMOVE TRANSMISSION CASE GASKET


    C161616
  1. Remove the 3 gaskets.



16. REMOVE BRAKE DRUM GASKET


    C161617
  1. Remove the 3 gaskets.



17. REMOVE CHECK BALL BODY


    C161618E01
  1. Remove the check ball body and spring.



18. REMOVE C-2 ACCUMULATOR PISTON


    C161619
  1. While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 and B-3 accumulator pistons may jump out.



19. REMOVE B-3 ACCUMULATOR PISTON


    C161619
  1. While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 accumulator piston may jump out.



20. REMOVE C-3 ACCUMULATOR PISTON


    C161620
  1. While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.



21. REMOVE B-1 ACCUMULATOR VALVE


    C161621
  1. Remove the B-1 accumulator valve and 2 springs.



22. REMOVE PARKING LOCK PAWL BRACKET


    C161622
  1. Remove the 3 bolts and bracket.



23. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C161623E01
  1. Disconnect the parking lock rod from the manual valve lever.



24. REMOVE PARKING LOCK PAWL


    C161624E01
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.



25. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D027918E01
  1. Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.



    C161626
  1. Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly tap out the spring pin so that it does not fall into the transmission case.

  1. Pull the manual valve lever shaft out through the transmission case, and remove the manual valve lever.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C161628
  1. Using a screwdriver, pry out the 2 oil seals.

    NOTICE:
    Be careful not to damage the transmission case.

    HINT:
    Wrap the tip of the screwdriver with tape before use.



27. REMOVE OIL PUMP ASSEMBLY


    C161629
  1. Remove the 10 bolts.



    C161630E01
  1. Using SST, pull out the oil pump.

    SST
    09950-40011   (09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031)



    C161631
  1. Remove the 2 thrust bearing races and O-ring from the oil pump.



28. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    C161632
  1. Remove the clutch drum and input shaft drum assembly from the transmission case.



    C161633
  1. Remove the clutch drum thrust washer and 2 thrust needle roller bearings.



29. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY


    C161779E01
  1. Hold the reverse clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.



30. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY


    C161634
  1. Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.



31. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    C161636E01
  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.



32. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


    C161637
  1. Using a screwdriver, remove the snap ring.



    C161638
  1. Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly with the rear clutch disc set from the clutch drum.



33. REMOVE REAR CLUTCH DISC SET


    C161640
  1. Remove the selective reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.



    C162148
  1. Remove the reverse clutch flange from the clutch drum.



34. INSPECT REAR CLUTCH DISC


    C162758
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



35. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY


    C161792
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

    Standard inside diameter:
    41.912 to 41.937 mm (1.410 to 1.411 in.)

    1. If the inside diameter is greater than the standard inside diameter, replace the reverse clutch hub.



36. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    C161641
  1. Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.



37. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY


    C161791
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

    Standard inside diameter:
    30.200 to 30.225 mm (1.189 to 1.190 in.)

    1. If the inside diameter is greater than the standard, replace the forward clutch hub.



38. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY


    C161642
  1. Remove the 2 thrust needle roller bearings, coast clutch hub with the No. 4 1-way clutch and thrust bearing race from the clutch drum.



39. INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY


    C161784E01
  1. Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.



40. REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY


    C161643
  1. Separate the No. 4 1-way clutch from the coast clutch hub.

  1. Remove the No. 2 clutch hub thrust washer from the coast clutch hub.



41. REMOVE FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC SET


    C161644
  1. Using a screwdriver, remove the hole snap ring.



    C161645E01
  1. Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.



42. INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC


    C161790
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



43. REMOVE COAST CLUTCH DISC SET


    C161646
  1. Using a screwdriver, remove the hole snap ring.



    C161647
  1. Remove the flange, 4 discs and 4 plates from the input shaft.



44. INSPECT COAST CLUTCH DISC


    C161789
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



45. REMOVE INPUT SHAFT SUB-ASSEMBLY


    C161648
  1. Remove the input shaft from the clutch drum.



46. REMOVE INPUT SHAFT OIL SEAL RING


    C161649
  1. Remove the 4 oil seal rings from the input shaft.



47. REMOVE COAST CLUTCH PISTON


    C161650E01
  1. Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    C161651
  1. Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.



    C161652
  1. Remove the O-ring from the No. 1 clutch balancer.



    C161653
  1. Hold the coast clutch piston by hand and apply compressed air to the input shaft to remove the coast clutch piston.



48. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY


    C161654
  1. Hold the forward clutch piston by hand and apply compressed air to the input shaft to remove the forward clutch piston.



    C162744
  1. Remove the O-ring from the input shaft.



49. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C161788
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    29.65 mm (1.17 in.)



50. REMOVE DIRECT CLUTCH DISC SET


    C159654
  1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum.



    C161655
  1. Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.



51. INSPECT DIRECT CLUTCH DISC


    C161787
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



52. REMOVE NO. 3 CLUTCH BALANCER


    C161656E01
  1. Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

    SST
    09380-60010   (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080, 09381-06070)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the No. 3 clutch balancer.



    C161657
  1. Remove the reverse clutch return spring and O-ring from the reverse clutch piston sub-assembly.



53. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    C161786
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.24 mm (0.836 in.)



54. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


    C161700
  1. Remove the reverse clutch piston from the clutch drum.



    C161702
  1. Remove the O-ring from the reverse clutch piston.



    C161703
  1. Remove the O-ring from the clutch drum.



55. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C161704E01
  1. Place SST on the direct clutch piston, and compress the return spring with a press.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum onto the oil pump.



    C161705E01
  1. Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston with the No. 2 clutch balancer and direct clutch return spring sub-assembly.



    C161706
  1. Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.



    C161812
  1. Remove the 2 O-rings from the direct clutch piston.



56. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    C161785
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.46 mm (0.766 in.)



57. REMOVE NO. 3 BRAKE SNAP RING


    C161635
  1. Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.



58. REMOVE NO. 3 BRAKE DISC SET


    C161707
  1. Remove the 2 flanges, 4 discs and 3 plates from the transmission case.



59. INSPECT NO. 3 BRAKE DISC


    C161778
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



60. REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING


    C161708E01
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)



61. REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C161709
  1. Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.



62. REMOVE NO. 3 BRAKE PISTON


    C162151E01
  1. Using SST and a press, compress the return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

    SST
    09380-60010   (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)



    C161712
  1. Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.



    C161713
  1. Remove the 2 O-rings from the No. 3 brake piston.



63. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C161777
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)



64. REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY


    C161710
  1. Remove the 1-way clutch with 1-way clutch inner race from the transmission case.



65. INSPECT 1-WAY CLUTCH ASSEMBLY


    C161775E01
  1. Install the 1-way clutch to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch from the 1-way clutch inner race.



66. REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY


    C161711
  1. Separate the 1-way clutch inner race from the 1-way clutch and remove the No. 1 planetary carrier thrust washer.



67. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    C161714
  1. Remove the front planetary gear and thrust needle roller bearing from the transmission case.



    C161715
  1. Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear.



68. INSPECT FRONT PLANETARY GEAR ASSEMBLY


    C161773
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    1. If the clearance is greater than the standard, replace the front planetary gear assembly.



    C161774
  1. Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

    Standard inside diameter:
    61.005 to 61.030 mm (2.402 to 2.403 in.)

    1. If the inside diameter is greater than the standard, replace the front planetary gear.



69. REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR


    C161716
  1. Remove the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear from the transmission case.

  1. Remove the thrust needle roller bearing and thrust bearing race.



70. REMOVE FRONT PLANETARY RING GEAR


    C161717
  1. Using a screwdriver, remove the snap ring.



    C161718
  1. Remove the front planetary ring gear from the center planetary ring gear.



71. REMOVE CENTER PLANETARY RING GEAR


    C161719
  1. Using a screwdriver, remove the snap ring.



    C161720
  1. Remove the center planetary ring gear from the front planetary ring gear flange.



72. REMOVE NO. 1 BRAKE DISC SET


    C161721
  1. Remove the flange, 4 discs and 4 plates from the transmission case.



73. INSPECT NO. 1 BRAKE DISC


    C161776
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



74. REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON


    C162153E01
  1. Place SST on the No. 1 brake piston return spring, and compress the return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)

  1. Using a screwdriver, remove the snap ring from the transmission case.



    C161723
  1. Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.



75. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C161772
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)



76. REMOVE NO. 1 BRAKE PISTON


    C161724
  1. Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



    C162732
  1. Remove the 2 O-rings from the No. 1 brake piston.



77. REMOVE NO. 2 BRAKE DISC SET


    C162561E01
  1. Place SST on the No. 2 brake flange, and compress the return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)

  1. Using a screwdriver, remove the snap ring from the transmission case.



    C161726
  1. Remove the 2 flanges, 4 discs, 3 plates and brake piston return spring from the transmission case.



78. INSPECT NO. 2 BRAKE DISC


    C161770
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



79. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C161771
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    22.66 mm (0.892 in.)



80. REMOVE CENTER PLANETARY GEAR ASSEMBLY


    C161727
  1. Remove the center planetary gear and planetary sun gear from the transmission case.



81. INSPECT CENTER PLANETARY GEAR ASSEMBLY


    C161749
  1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    1. If the clearance is greater than the standard, replace the center planetary gear assembly.



82. REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON


    C161728
  1. Remove the No. 2 brake cylinder with the No. 2 brake piston from the transmission case.



83. REMOVE NO. 2 BRAKE PISTON


    C162149
  1. Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



    C162730
  1. Remove the 2 O-rings from the No. 2 brake piston.



84. REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR


    C161730E01
  1. Using SST, remove the snap ring from the transmission case.

    SST
    09350-30020   (09350-07060)



    C161731
  1. Remove the intermediate shaft with No. 3 1-way clutch, rear planetary ring gear flange and rear planetary ring gear from the transmission case.



85. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY


    C161748E01
  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



86. REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY


    C161732
  1. Remove the No. 3 1-way clutch and 1-way clutch inner race from the intermediate shaft.



87. REMOVE REAR PLANETARY RING GEAR


    C161733
  1. Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.



    C161734
  1. Using a screwdriver, remove the snap ring.

  1. Remove the rear planetary ring gear flange from the rear planetary ring gear.



88. INSPECT INTERMEDIATE SHAFT


    C161746E01
  1. Using a dial indicator, check the intermediate shaft runout.

    Standard runout:
    0.03 mm (0.00118 in.)

    If the runout is greater than the standard, replace the intermediate shaft with a new one.



    C161747E01
  1. Using a micrometer, check the outer diameter of the intermediate shaft at the positions shown in the diagram.

    Standard Diameter:
    Bolt
    Bolt Length
    A
    19.963 to 19.976 mm (0.7859 to 0.7865 in.)
    B, C
    30.150 to 30.163 mm (1.187 to 1.188 in.)
    D, E
    36.404 to 36.420 mm (1.433 to 1.434 in.)

    If the diameter is less than the standard, replace the intermediate shaft with a new one.



89. REMOVE NO. 4 BRAKE DISC SET


    C161736
  1. Remove the 2 flanges, 7 discs and 6 plates from the transmission case.



90. INSPECT NO. 4 BRAKE DISC


    C161745
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.



91. REMOVE BRAKE PLATE STOPPER SPRING


C161735

NOTICE:
When removing the stopper spring, do not apply excessive force and do not deform it.



92. REMOVE REAR PLANETARY GEAR ASSEMBLY


    C161610
  1. Using snap ring expander, remove the snap ring.



    C161611
  1. Remove the rear planetary flange thrust bearing race, thrust needle roller bearing and thrust bearing race.



    C161737
  1. Remove the rear planetary gear from the transmission case.



    C161738
  1. Remove the 2 thrust needle roller bearings from the rear planetary gear.



    C161739
  1. Remove the thrust bearing race from the transmission case.



93. INSPECT REAR PLANETARY GEAR ASSEMBLY


    C161743
  1. Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    1. If the clearance is greater than the standard, replace the planetary gear assembly.



    C161744
  1. Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

    Standard inside diameter:
    20.0 to 20.025 mm (0.787 to 0.788 in.)

    1. If the inside diameter is greater than the standard, replace the rear planetary gear assembly.



94. REMOVE 1ST AND REVERSE BRAKE PISTON


    C162152E01
  1. Place SST on the spring retainer and compress the brake return spring.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)



    C161740
  1. Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



    C161741
  1. Remove the 3 O-rings from the 1st and reverse brake piston.



95. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C161742
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.54 to 23.94 mm (0.927 to 0.943 in.)