RADIATOR > INSTALLATION |
| 1. INSTALL OUTLET RADIATOR HOSE |
![]() |
Install the outlet radiator hose into the radiator.
| 2. INSTALL RADIATOR ASSEMBLY |
![]() |
Set the radiator bracket hooks to the radiator support holes.
Install the radiator with the 4 bolts.
| 3. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for LH Side) |
![]() |
Install the No. 1 radiator to support seal with the 3 clips.
| 4. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for RH Side) |
![]() |
Install the No. 1 radiator to support seal with the 3 clips.
| 5. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Install the deflector with the 6 clips.
Connect the wire harness clamp.
| 6. INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Trailer Towing System) |
![]() |
Install the deflector with the 6 clips.
| 7. INSTALL FAN SHROUD (w/ Trailer Towing System) |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
![]() |
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 8. INSTALL FAN SHROUD (w/o Trailer Towing System) |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 9. INSTALL INLET RADIATOR HOSE |
![]() |
Install the inlet radiator hose.
| 10. CONNECT OUTLET RADIATOR HOSE |
![]() |
Connect the outlet radiator hose to the water inlet housing.
| 11. INSTALL OIL COOLER ASSEMBLY (w/ Trailer Towing System) |
![]() |
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the oil cooler.
![]() |
Install the oil cooler with the 5 nuts.
| 12. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 14.6 liters (15.4 US qts., 12.8 Imp. qts.) |
| w/o Trailer Towing System | 13.6 liters (14.4 US qts., 12.0 Imp. qts.) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 13. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 14. INSTALL NO. 1 FRONT BUMPER SIDE RETAINER SUB-ASSEMBLY RH (w/ Trailer Towing System) |
| 15. INSTALL FRONT BUMPER COVER ASSEMBLY |
Install the front bumper cover assembly (Click here).
| 16. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 17. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.