Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here



1. INSTALL NO. 5 BACK DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 5 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B211074E01
  1. Install a new No. 5 back door name plate as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    54.2 mm (2.13 in.)
    b
    95.4 mm (3.76 in.)
    c
    53.9 mm (2.12 in.)

    NOTICE:
    Install the No. 5 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 5 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 5 back door name plate.



2. INSTALL NO. 3 BACK DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 3 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B191718E01
  1. Install a new No. 3 back door name plate as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    99.2 mm (3.91 in.)
    b
    104.5 mm (4.11 in.)
    c
    98.6 mm (3.88 in.)

    NOTICE:
    Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.



3. INSTALL NO. 4 BACK DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 4 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B191719E01
  1. Install a new No. 4 back door name plate as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    112.8 mm (4.44 in.)
    b
    87.8 mm (3.46 in.)
    c
    113.9 mm (4.48 in.)

    NOTICE:
    Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.



4. INSTALL SYMBOL EMBLEM


    B117713E02
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Insert the 2 pins into the back door panel and install the symbol emblem.

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.



5. INSTALL NO. 1 ROOF SIDE MARK
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B191720E01
  1. Install a new No. 1 roof side mark as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    4.6 mm (0.181 in.)
    b
    19.5 mm (0.768 in.)
    c
    4.6 mm (0.181 in.)
    d
    4.6 mm (0.181 in.)
    e
    16.3 mm (0.642 in.)
    f
    4.6 mm (0.181 in.)

    NOTICE:
    Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.



6. INSTALL NO. 1 ROOF SIDE MARK
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B191721E01
  1. Install a new No. 1 roof side mark as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    4.6 mm (0.181 in.)
    b
    26.6 mm (1.05 in.)
    c
    4.6 mm (0.181 in.)
    d
    4.6 mm (0.181 in.)
    e
    16 mm (0.630 in.)
    f
    4.6 mm (0.181 in.)

    NOTICE:
    Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.



7. INSTALL NO. 1 ROOF SIDE MARK
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B209749E01
  1. Install a new No. 1 roof side mark as shown in the illustration.

    Installation Position:
    Mark
    Measurement (Along Surface)
    a
    4.7 mm (0.185 in.)
    b
    33.6 mm (1.32 in.)
    c
    4.5 mm (0.177 in.)
    d
    4.4 mm (0.173 in.)
    e
    34.1 mm (1.34 in.)
    f
    4.5 mm (0.177 in.)

    NOTICE:
    Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.