Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 3UR-FE, 3UR-FBE)

VANE PUMP (for 3UR-FE, 3UR-FBE) > REASSEMBLY

for Preparation Click here


NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).



1. INSTALL VANE PUMP HOUSING OIL SEAL


    C114702E01
  1. Coat the lip of a new oil seal with power steering fluid.

  1. Using SST and a press, press in the oil seal.

    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.



2. INSTALL VANE PUMP SHAFT SUB-ASSEMBLY WITH PULLEY


    C114703E01
  1. Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.

  1. Gradually insert the vane pump shaft sub-assembly with pulley.

    NOTICE:
    1. Do not damage the lip of the oil seal in the front housing.
    2. Wrap protective tape around the spline of the vane pump shaft with vane pump shaft sub-assembly with pulley in order to prevent damage to the oil seal.



3. INSTALL VANE PUMP FRONT SIDE PLATE


    C132035
  1. Coat a new O-ring with power steering fluid and install it into the front housing.



    C107035
  1. Coat a new O-ring with power steering fluid and install it onto the front side plate.



    C132040E01
  1. Align the notch of the front side plate with the notch of the front housing, and install the front side plate.

    NOTICE:
    Make sure that the front side plate is installed facing in the correct direction.



4. INSTALL VANE PUMP CAM RING


    C139139E01
  1. Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.

    NOTICE:
    Make sure that the cam ring is installed facing in the correct direction.



5. INSTALL VANE PUMP ROTOR


    C107038
  1. Install the vane pump rotor.

    HINT:
    The vane pump rotor can be installed in both directions.

  1. Coat the 10 vane pump plates with power steering fluid.



    C141370E01
  1. Install the vane pump plates with the round end facing outward.

    NOTICE:
    Make sure that the vane pump plates are installed facing in the correct direction.



6. INSTALL VANE PUMP SHAFT SNAP RING


    D030336E01
  1. Using a screwdriver and snap ring expander, install a new shaft snap ring onto the vane pump shaft.



7. INSTALL VANE PUMP REAR HOUSING


    C107040
  1. Coat a new O-ring with power steering fluid and install it onto the rear housing.



    C136780E01
  1. Align the straight pin of the rear housing with the notches of the cam ring, front side plate, and front housing.



    C131230
  1. Install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



8. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install the service bolt.

    Recommended service bolt:
    Thread diameter
    Thread pitch
    Bolt length
    10 mm (0.394 in.)
    1.25 mm (0.0492 in.)
    50 mm (1.97 in.)



    C053369E10
  1. Using a torque wrench, measure the pumps rotating torque.

    Standard rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    If the rotating torque is not as specified, check the vane pump housing oil seal.



9. INSTALL POWER STEERING SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.



    C181330
  1. Install the suction port union to the vane pump with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }