Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



2. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



3. REMOVE INSTRUMENT SIDE PANEL LH


    B192331E01
  1. Apply protective tape, as shown in the illustration.

  1. Using a moulding remover, disengage the 3 claws and 4 guides and remove the side panel.



4. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Disengage the 3 claws.

  1. Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.



5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B192333
  1. Remove the 2 <A> bolts.

  1. Disengage the 4 clips and claw.

  1. Disengage the 2 claws and separate the sensor.

  1. Disconnect the connectors and remove the finish panel.



6. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT


B192337
  1. Remove the 4 <A> bolts.

  1. Disengage the 2 claws.

  1. Disconnect the connector and clamp and remove the safety pad insert.



7. RELEASE PARKING BRAKE PEDAL


8. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C154230
  1. Remove the lock nut and adjustment nut.



    C154232
  1. Remove the clip.



    C155437
  1. Using a screwdriver, slowly bend up the claw.

    NOTICE:
    Be careful not to damage the No. 1 parking brake cable or claw.

  1. Disconnect the parking brake cable from the parking brake control pedal.



9. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for 3UR-FE)


A184927
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the front No. 3 exhaust pipe sub-assembly from the exhaust pipe support.

  1. Remove the front No. 3 exhaust pipe sub-assembly from the front No. 2 exhaust pipe sub-assembly assembly.

  1. Disconnect the air fuel ratio sensor connector.



    A184928
  1. Remove the 3 nuts, front No. 2 exhaust pipe sub-assembly and 2 gaskets from the exhaust manifold LH.



10. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY (for 2UZ-FE)


    A185593
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the exhaust pipe support and remove the front No. 3 exhaust pipe sub-assembly.

  1. Remove the gasket from the front No. 2 exhaust pipe assembly.



11. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for 2UZ-FE)


    A185595
  1. Disconnect the air fuel ratio sensor connector.



    A185596
  1. Disconnect the heated oxygen sensor connector.



    A185602
  1. Remove the 3 nuts and remove the front No. 2 exhaust pipe assembly.



12. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY
  1. Remove the adjustment nut and lock nut (labeled A).

  1. Remove the bolt (labeled B) and cable retainer.

  1. Remove the nut (labeled C) and clamp from the body.

  1. Disconnect the clamp (labeled D) from the No. 1 parking brake cable.



  1. Remove the 2 bolts (labeled E) and No. 1 parking brake cable from the inside of the vehicle.

    NOTICE:
    Do not bend and twist the parking brake cable.



    C183663E01



13. REMOVE REAR WHEEL LH


14. REMOVE REAR WHEEL RH


15. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH


    C158344
  1. Remove the 2 bolts and disconnect the rear disc brake cylinder.

    NOTICE:
    1. Do not disconnect the flexible hose from the disc brake cylinder.
    2. Do not twist or bend the flexible hose.

  1. Hang the disc brake cylinder with a piece of wire.



16. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedure for both sides.



17. REMOVE REAR DISC LH


    C178157E01
  1. Put matchmarks on the rear disc and axle hub if planning to reuse the disc.



    C155453
  1. Turn the shoe adjuster until the disc turns freely, and then remove the disc.



18. REMOVE REAR DISC RH

HINT:
Use the same procedure for both sides.



19. REMOVE PARKING BRAKE SHOE RETURN SPRING LH


    C191839E01
  1. Using SST, remove the return spring.

    SST
    09703-30011  



20. REMOVE PARKING BRAKE SHOE RETURN SPRING RH

HINT:
Use the same procedure for both sides.



21. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY LH


    C155124E01
  1. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring pin.

    SST
    09718-00011  

  1. Disconnect the tension spring.

  1. Remove the No. 1 parking brake shoe and shoe adjuster screw set.



22. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedure for both sides.



23. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY LH


    C154249E01
  1. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring pin.

    SST
    09718-00011  

  1. Remove the No. 2 parking brake shoe.



24. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedure for both sides.



25. REMOVE PARKING BRAKE SHOE LEVER LH


    C155125
  1. Disconnect the No. 3 parking brake cable from the parking brake shoe lever.

  1. Remove the parking brake shoe lever.



26. REMOVE PARKING BRAKE SHOE LEVER RH

HINT:
Use the same procedure for both sides.



27. REMOVE INTERMEDIATE LEVER TENSION SPRING


    C156990
  1. Remove the tension spring.



28. REMOVE NO. 2 CABLE RETAINER


    C156991
  1. Remove the bolt and cable retainer.



29. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


C180582
  1. Disconnect the No. 3 parking brake cable from the intermediate lever.



  1. Remove the 4 bolts and disconnect the No. 3 parking brake cable from the frame.

    NOTICE:
    Do not bend and twist the parking brake cable.



    C181281



    C154244
  1. Remove the bolt and No. 3 parking brake cable from the rear axle carrier.



30. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY



C180575E01

HINT:
The No. 2 parking brake cable bolt locations are symmetric to those of the No. 3 parking brake cable, with the exception of the locations indicated with "*A".

  1. Disconnect the No. 2 parking brake cable from the intermediate lever.

  1. Remove the 8 bolts and disconnect the No. 2 parking brake cable from the frame.

  1. Remove the bolt and the No. 2 parking brake cable from the rear axle carrier.