Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A067628E24
  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).
  2. The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
When either condition below is met:
  1. The intake air temperature change is small, from the previous trip warm-up to the following trip (2 trip detection logic).
  2. When the change in the intake air temperature after engine start is less than the threshold value.
Mass air flow meter assembly

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects the stuck intake air temperature sensor value by performing monitoring after the ignition switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY


Related DTCs
P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors/Components (Main)
Intake Air Temperature (IAT) sensor
Required Sensors/Components (Sub)
-
Frequency of Operation
Once per driving cycle
Duration
10 seconds or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not present
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0102, P0103 (Mass air flow meter)

After Engine Stop 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or more
ECT change since engine stop
-40°C (-40°F) or more
ECT before engine stop
70°C (158°F) or more
Accumulated MAF amount before engine stop
5752 g or more
Key-off duration
30 minutes

After Cold Engine Start 
Key-off duration
5 hours
Time after engine start
10 seconds or more
ECT
70°C (158°F) or more
Accumulated MAF amount
5752 g or more
Either of the following conditions 1 or 2 is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


After Engine Stop 
IAT change
Less than 1°C (2°F)

After Cold Engine Start 
IAT change
Less than 1°C (2°F)

WIRING DIAGRAM

Refer to DTC P0110 .

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0111 and other DTCs are output
    A
    P0111 is output
    B

    HINT:
    If any DTCs other than P0111 are output, troubleshoot those DTCs first.



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART (Click here)