Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > Power Source Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the fold seat control ECU through the L1 RR2 SEAT*1, L2 RR2 SEAT*1, R1 RR2 SEAT*2 and R2 RR2 SEAT*2 fuses.
  1. *1: LH Side
  2. *2: RH Side

WIRING DIAGRAM


B195053E01


INSPECTION PROCEDURE

1.INSPECT FUSE


    B188606E04
  1. Remove the L1 RR2 SEAT, L2 RR2 SEAT, R1 RR2 SEAT and R2 RR2 SEAT fuses from the engine room relay block.

  1. Remove the ECU-IG No. 2 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 2 fuse
    Always
    Below 1 Ω
    L1 RR2 SEAT fuse
    Always
    Below 1 Ω
    L2 RR2 SEAT fuse
    Always
    Below 1 Ω
    R1 RR2 SEAT fuse
    Always
    Below 1 Ω
    R2 RR2 SEAT fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    B194780E02
  1. Disconnect the O33 and O34 or P19 and P20 ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    O33-4 (+B) - Body ground
    Always
    11 to 14 V
    O33-10 (+B2) - Body ground
    Always
    11 to 14 V
    O34-3 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    P19-4 (+B) - Body ground
    Always
    11 to 14 V
    P19-10 (+B2) - Body ground
    Always
    11 to 14 V
    P20-3 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)


    B194832E03
  1. Disconnect the O33 or P19 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    O33-8 (GND) - Body ground
    Always
    Below 1 Ω
    O33-9 (GND2) - Body ground
    Always
    Below 1 Ω
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    P19-8 (GND) - Body ground
    Always
    Below 1 Ω
    P19-9 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE