Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

H100802E08

  1. Disconnect the O30 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-10 (ECUB) - Body ground
    R - Body ground
    ECUB power supply
    Always
    11 to 14 V
    O30-12 (B) - Body ground
    L - Body ground
    B power supply
    Always
    11 to 14 V
    O30-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    O30-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    O30-17 (MSW) - Body ground
    L - Body ground
    Power back door main switch signal circuit
    Power back door main switch not pushed
    Below 1 Ω
    O30-17 (MSW) - Body ground
    L - Body ground
    Power back door main switch signal circuit
    Power back door main switch pushed
    10 kΩ or higher
    O30-20 (FUL) - Body ground
    R - Body ground
    Back door courtesy light switch signal circuit
    Back door is opened
    Below 1 Ω
    O30-20 (FUL) - Body ground
    R - Body ground
    Back door courtesy light switch signal circuit
    Back door is closed
    10 kΩ or higher
    O30-4 (DS1) - Body ground
    SB - Body ground
    Back door closer switch signal circuit
    Back door closer switch ON
    Below 1 Ω
    O30-4 (DS1) - Body ground
    SB - Body ground
    Back door closer switch signal circuit
    Back door closer switch OFF
    10 kΩ or higher
    O30-15 (OSL) - O30-14 (OSE)
    LG - Y
    Power back door touch sensor LH circuit
    Back door touch sensor LH not pressed
    950 to 1050 Ω
    O30-15 (OSL) - O30-14 (OSE)
    LG - Y
    Power back door touch sensor LH circuit
    Back door touch sensor LH pressed
    Below 100 Ω
    O30-13 (OSR) - O30-14 (OSE)
    BR - Y
    Power back door touch sensor RH circuit
    Back door touch sensor RH not pressed
    950 to 1050 Ω
    O30-13 (OSR) - O30-14 (OSE)
    BR - Y
    Power back door touch sensor RH circuit
    Back door touch sensor RH pressed
    Below 100 Ω
    O30-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the O30 ECU connector.

  4. Measure the voltage according to the value(s) in the table below:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-26 (BZR+) - Body ground
    P - Body ground
    Power back door warning buzzer signal input
    Back door warning buzzer is sounding
    11 to 14 V
    O30-26 (BZR+) - Body ground
    P - Body ground
    Power back door warning buzzer signal input
    Back door warning buzzer is stopped
    Below 1 V
    O30-2 (DC+) - O30-1 (DC-)
    P - SB
    Power back door lock motor circuit
    Back door lock motor is operating
    11 to 14 V
    O30-2 (DC+) - O30-1 (DC-)
    P - SB
    Power back door lock motor circuit
    Back door lock motor is stopped
    Below 1 V
    O30-22 (HAF) - Body ground
    V - Body ground
    Back door lock half-latch switch signal circuit
    Back door is opened →
    Back door closer motor is operating →
    Back door is closed
    Below 1 V →
    11 to 14 V →
    Below 1 V
    O30-24 (POS) - Body ground
    O - Body ground
    Back door lock position switch signal circuit
    Back door is opened →
    Back door closer motor is operating →
    Back door is closed
    Below 1 V →
    11 to 14 V →
    Below 1 V

    HINT:
    If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C172609E07

  1. Disconnect the DD and H4 connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H4-26 (PBDS) - Body ground
    R - Body ground
    Power back door open/close switch signal circuit
    Power back door open/close switch ON
    Below 1 Ω
    H4-26 (PBDS) - Body ground
    R - Body ground
    Power back door open/close switch signal circuit
    Power back door open/close switch OFF
    10 kΩ or higher
    DD-62 (GND1,GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.