Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Ignition Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU determines the ignition switch position (off, ACC, ON) based on signals from the IG or ACC circuit.

WIRING DIAGRAM


B209245E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream main switch on.

  1. Select the items below in the Data List and read the display on the Techstream.

    Main Body 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Ignition switch ON signal ON/OFF
    ON: Ignition switch is ON
    OFF: Ignition switch is off
    -
    ACC SW
    Ignition switch ACC signal ON/OFF
    ON: Ignition switch is ACC
    OFF: Ignition switch is off
    -

    OK:
    When the ignition switch is operated, the display changes as shown in the table.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSES (AM1, ECU-IG No. 2)


    B188612E04
  1. Remove the AM1 and ECU-IG No. 2 fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AM1 fuse
    Always
    Below 1 Ω
    ECU-IG No. 2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)


    B165958E01
  1. Disconnect the DA main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT IGNITION SWITCH ASSEMBLY


    B125076E03
  1. Disconnect the H10 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 4
    Ignition switch ON
    Below 1 Ω
    2 - 4
    Ignition switch ACC
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IGNITION SWITCH AND BODY GROUND)


    B165959E02
  1. Disconnect the DD main body ECU connector.

  1. Disconnect the H10 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-47 - H10-4 (AM1)
    Always
    Below 1 Ω
    DD-43 - H10-1 (IG1)
    Always
    Below 1 Ω
    DD-45 - H10-2 (ACC)
    Always
    Below 1 Ω
    DD-62 - Body ground
    Always
    Below 1 Ω
    DD-47 - Body ground
    Always
    10 kΩ or higher
    DD-43 - Body ground
    Always
    10 kΩ or higher
    DD-45 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU