Home › Engine / Hybrid System ยท 2UZ-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY

NOTICE:
  1. Be careful not to drop the injectors when installing the delivery pipes.
  2. Do not apply any load to the injector in the horizontal direction.



    A185333E01
  1. Apply a light coat of gasoline to each new O-ring and install one to each injector.



    A133664E01
  1. Install the 8 injectors.

    1. While turning each injector clockwise and counterclockwise, push it onto the delivery pipes.

    2. Position the injector connectors outward.

  1. Place 8 new insulators on the intake manifold.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the injectors when installing the delivery pipes.



    A162032E01
  1. Place the 2 delivery pipes and injector assemblies on the lower intake manifold.

  1. Temporarily install the 4 nuts.

  1. Install the No. 1 fuel pipe sub-assembly with the bolt, 4 new gaskets and 2 union bolts.

    1. for union bolt

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    1. for bolt

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A160921
  1. Install the fuel return pipe with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A160920
  1. Connect the fuel return hose to the fuel pressure regulator.



    A133665E02
  1. Check that the injectors rotate smoothly.

    HINT:
    If the injectors do not rotate smoothly, a probable cause is the incorrect installation of the O-rings. Replace the O-ring of the injector that does not rotate smoothly.

  1. Position the injector connectors outward.

  1. Tighten the 4 nuts holding the delivery pipes to the lower intake manifold.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the 8 injector connectors.



3. INSTALL ENGINE WIRE


    A160928
  1. Install the 2 wire clamps on the engine wire to the brackets on the RH delivery pipe.

  1. Connect the engine wire clamps to the No. 1 engine hanger and engine wire bracket.

  1. Install the engine wire protector with the 2 bolts.



4. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


A160926
  1. Connect the No. 2 fuel pipe sub-assembly (Click here).

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



5. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


A187100E02
  1. Connect the No. 1 fuel pipe sub-assembly.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



6. INSTALL EFI FUEL PIPE CLAMP


A185283
  1. Install the fuel pipe clamp.



7. INSTALL THROTTLE BODY COVER BRACKET
  1. Install the 2 throttle body cover brackets with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



8. CONNECT NO. 2 VENTILATION HOSE
  1. Connect the No. 2 ventilation hose to the ventilation valve.



9. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E02
  1. Install the air cleaner hose assembly with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose and No. 2 ventilation hose.



10. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



11. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

    NOTICE:
    Do not start the engine.

  1. Techstream:
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



    A133618E01
  1. Check that the pulsation damper screw rises up when the fuel pump operates.
    If the operation is not as specified, check the following parts:

    1. Fusible link
    2. Fuses
    3. Circuit opening relay
    4. Fuel pump
    5. ECM
    6. Wiring connections
    If no malfunctions are found in the aforementioned components, replace the pulsation damper.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.