Home › Engine / Hybrid System ยท 2UZ-FE › EMISSION CONTROL › AIR PUMP

AIR PUMP > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 AIR PUMP BRACKET


    A153501
  1. Install the pump to the No. 1 air pump bracket with the 3 air pump insulators.

  1. Install the clamp.



2. INSTALL NO. 1 AIR INJECTION SYSTEM HOSE


3. INSTALL AIR PUMP INLET


    A153502E01
  1. Install the air pump inlet with the 2 bolts as shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Fully the insert hose to the stoppers.



4. INSTALL AIR PUMP ASSEMBLY (for Bank 2)


    A153503E01
  1. Insert the slot over the stud and bracket tab into the slot (View A).

  1. Insert the bracket tab into the slot (View B).

  1. Install the 2 nuts and bolt.

    1. for bolt

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    1. for nut

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



5. INSTALL NO. 2 AIR INJECTION SYSTEM HOSE


    A158138E02
  1. Install the No. 2 air injection system hose as shown in the illustration.



    A153497
  1. Connect the air pump assembly connector.

  1. Connect the 2 clamps.



    A153461
  1. Install the fender apron seal with the 2 clips.



6. INSTALL FRONT FENDER LINER RH


    A160255
  1. Install the front fender liner RH with the 9 clips.



7. INSTALL AIR PUMP BRACKET


    A159763E01
  1. Install the air pump bracket, 3 insulators and 3 collars with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL AIR PUMP ASSEMBLY (for Bank 1)


    A185662
  1. Install the air pump assembly with the 2 bolts and 2 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Connect the air pump assembly connector.



9. INSTALL NO. 1 AIR INJECTION SYSTEM HOSE


    A185663E01
  1. Install the No. 1 air injection system hose as shown in the illustration.



10. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Install a new O-ring to the water by-pass pipe sub-assembly.

  1. Apply soapy water to the O-ring.



    A162643
  1. Push in the water by-pass pipe sub-assembly.

  1. Connect the water by-pass pipe sub-assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector clamp.



11. INSTALL INTAKE MANIFOLD


    A156181
  1. Place 2 new gaskets on the intake manifold assembly.

  1. Place the intake manifold assembly on the cylinder heads.



    A156172
  1. Install and uniformly tighten the 6 bolts and 4 nuts in several steps.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    A156173
  1. Install the engine wire protector with the 2 bolts.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }

  1. Connect the 8 injector connectors.



    A163553
  1. Connect the 2 wire clamps.



    A166384
  1. Connect the vacuum switching valve assembly (for ACIS) connector.



    A166385
  1. Install the wire harness bracket to the intake manifold assembly with the bolt.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }


    1. Connect the wire harness clamp to the engine hanger.



    A156171
  1. Connect the purge line hose to the purge VSV.

  1. Connect the purge VSV connector.



    A166383
  1. Install the No. 1 ventilation hose with the 2 clamps.



    A156170
  1. Connect the 2 water by-pass hoses to the throttle body assembly.

  1. Connect the throttle body assembly connector.



12. INSTALL FUEL MAIN TUBE


A187100E02
  1. Connect the No. 1 fuel pipe sub-assembly.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



13. INSTALL FUEL RETURN TUBE


A160926
  1. Connect the No. 2 fuel pipe sub-assembly (Click here).

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



14. REMOVE NO. 2 WATER BY-PASS PIPE


    A156177
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.

  1. Install the No. 2 water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A156176
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.



15. CONNECT VACUUM HOSE ASSEMBLY


    A156175
  1. Connect the vacuum hose assembly to the intake manifold assembly.

  1. Install the vacuum hose assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



16. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E02
  1. Install the air cleaner hose assembly with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose and No. 2 ventilation hose.



17. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down.



    A151850E04
  1. If the coolant level is below the LOW line, repeat all of the procedures above.



18. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



19. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. for bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. for screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



20. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A156184E02
  1. Install the 2 throttle body cover brackets with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A156183E01
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



21. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY


  1. Install the front cowl top outer panel sub-assembly with the 7 bolts.


    A151796

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the wire harness clamp to the front cowl top outer panel sub-assembly.

  1. Install the washer hose grommet to the front cowl top outer panel sub-assembly.

  1. Connect the washer hose.



22. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Install the wiper motor and link assembly with the 4 bolts and nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



23. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161314
  1. Engage the 6 claws and 8 guides and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



24. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Engage the claw and install the front fender to cowl side seal.



25. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



26. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161321E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



27. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161322E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.