Home › Engine / Hybrid System ยท 2UZ-FE › COOLING › RADIATOR

RADIATOR > INSTALLATION

for Preparation Click here



1. INSTALL RADIATOR DRAIN COCK PLUG
  1. Install the radiator drain cock plug to the radiator assembly.



2. INSTALL OUTLET RADIATOR HOSE
  1. Install the outlet radiator hose to the radiator assembly.



3. INSTALL RADIATOR ASSEMBLY


A185309
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



4. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL


A185302E01
  1. Install the No. 1 radiator to support seal with the 3 clips.



5. CONNECT OUTLET RADIATOR HOSE


A185307
  1. Connect the outlet radiator hose.



6. INSTALL FAN SHROUD (w/ Trailer Towing System)
  1. Install the fan pulley to the water pump.

  1. Place the fan shroud together with the fluid coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A156169
  1. Attach the shroud claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A185330
  1. Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.

    HINT:
    Install hose clamp on center of white paint and install the lock section of the hose clamp into the stopper of the fan shroud.



    A185308
  1. Connect the reservoir hose.

  1. Install the fan and generator V-belt (Click here).



    A162053
  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



7. INSTALL FAN SHROUD (w/o Trailer Towing System)
  1. Install the fan pulley to the water pump.

  1. Place the fan shroud together with the fluid coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A156169
  1. Attach the shroud claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A185308
  1. Connect the reservoir hose.

  1. Install the fan and generator V-belt .



    A162053
  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



8. INSTALL INLET RADIATOR HOSE


A185306
  1. Connect the inlet radiator hose.



9. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E02
  1. Install the air cleaner hose assembly with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose and No. 2 ventilation hose.



10. INSTALL OIL COOLER ASSEMBLY (w/ Trailer Towing System)


    C179236
  1. Install the oil cooler support bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C179235
  1. Temporarily place the air cooled oil cooler assembly on the radiator support.

    HINT:
    Securely attach the claw of the oil cooler support bracket into the hole of the radiator support.

  1. Install the air cooled oil cooler assembly with the 3 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



11. INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Trailer Towing System)


A185305
  1. Install the deflector with the 6 clips.



12. INSTALL RADIATOR SIDE DEFLECTOR LH


A185304
  1. Install the deflector with the 6 clips.

  1. Install the wire harness clamp.



13. INSTALL FRONT BUMPER COVER
  1. Install the front bumper cover (Click here).



14. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down.



    A151850E04
  1. If the coolant level is below the LOW line, repeat all of the procedures above.



15. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



16. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


17. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



18. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. for bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. for screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }