ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT BATTERY |
Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the electrolyte quantity of each cell.
For maintenance-free batteries:
For non-maintenance-free batteries:
Turn the ignition switch off and turn on the headlight for 20 to 30 seconds. This will remove the surface charge from the battery.
![]() |
Measure the battery voltage between the negative (-) and positive (+) terminals of the battery.
![]() |
Reference:
The indicator shows the battery condition.
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air filter is not excessively damaged or oily. If necessary, replace the air filter.
| 5. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Check that the belt tensioner moves downward when the belt is pressed down at the point indicated in the illustration with approximately 98 N (10 kgf, 22.0 lbf) of force.
![]() |
Check that the arrow on the belt tensioner is within area "A".
If it is outside area "A", replace the fan and generator V belt.
| 6. INSPECT FAN AND GENERATOR V BELT |
![]() |
Check the belt for wear, cracks or other signs of damage.
If any of the following defects is found, replace the fan and generator V belt.
![]() |
Check that the belt fits properly in the ribbed grooves.
| 7. INSPECT IGNITION TIMING |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Start the engine and idle it.
Push the Techstream main switch ON.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Disconnect the timing light from the engine.
| 8. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Push the Techstream main switch ON.
Enter the following menus: / Engine / Data List / Engine Speed.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer from the DLC3.
| 9. INSPECT COMPRESSION |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
Remove the 2 nuts and throttle body cover.
Remove the air cleaner hose assembly.
Remove the air cleaner cap.
Disconnect the 8 injector connectors and 8 ignition coils.
Remove the 8 bolts and 8 ignition coils.
Remove the 8 spark plugs.
![]() |
Check the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.
Install the 8 spark plugs.
Install the 8 ignition coils with the 8 bolts.
Connect the 8 injector connectors and 8 ignition coils.
Install the air cleaner cap.
Install the air cleaner hose.
Install the throttle body cover with the 2 nuts.
| 10. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
![]() |
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2500 rpm.
If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.
Check the A/F sensor and heated oxygen sensor operation.
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|