Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM

FRONT UPPER SUSPENSION ARM > INSTALLATION

for Preparation Click here



1. TEMPORARILY INSTALL FRONT SUSPENSION UPPER ARM ASSEMBLY LH


C155976
  1. Temporarily install the suspension upper arm with the 2 washers, bolt and nut.

    HINT:
    After stabilizing the suspension, tighten the nut.



2. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the apron seal with the 5 clips.



3. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the apron seal with the 6 clips.



4. CONNECT STEERING KNUCKLE LH
  1. Connect the steering knuckle to the suspension upper arm.

  1. Install the nut and a new cotter pin.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.



5. CONNECT SKID CONTROL SENSOR WIRE


C155974E02
  1. Connect the sensor wire to the steering knuckle and upper arm with the 2 bolts.

    1. for Bolt A

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    1. for Bolt B

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



6. TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING LH


C155965
  1. Temporarily install the upper side of the shock absorber to the chassis frame with the 4 nuts.



    C155964
  1. Temporarily install the lower side of the shock absorber to the lower suspension arm with the bolt, washer and nut.



7. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.



8. TIGHTEN FRONT SUSPENSION UPPER ARM ASSEMBLY LH
  1. Tighten the nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 173 ft.*lbf }



9. TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


C155964
  1. Tighten the nut.

    Torque:
    195 N*m{ 1988 kgf*cm , 144 ft.*lbf }



    C163294E01
  1. Tighten the 4 upper nuts in diametrically opposite pairs.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

  1. Check that the first nut that was tightened is at the torque specification.



10. REMOVE SUSPENSION CONTROL BRACKET (w/ AVS)


C181282
  1. Install the suspension control bracket with the nut.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



11. REMOVE ABSORBER CONTROL ACTUATOR (w/ AVS)


C180592
  1. Using a hexagon wrench, install the absorber control actuator with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



    C180587
  1. Connect the absorber control actuator connector.



12. INSTALL FRONT WHEEL
  1. for Aluminum Wheel

Torque:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }

  1. for Steel Wheel

Torque:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



13. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)