CAMSHAFT POSITION SENSOR > INSTALLATION |
| 1. INSTALL VVT SENSOR |
![]() |
Install the 2 VVT sensors with the 2 bolts.
Connect the 2 VVT sensor connectors.
| 2. INSTALL INTAKE MANIFOLD |
![]() |
Place 2 new gaskets on the intake manifold assembly.
Place the intake manifold assembly on the cylinder heads.
![]() |
Install and uniformly tighten the 6 bolts and 4 nuts in several steps.
![]() |
Install the engine wire protector with the 2 bolts.
Connect the 8 injector connectors.
![]() |
Connect the 2 wire clamps.
![]() |
Connect the vacuum switching valve assembly (for ACIS) connector.
![]() |
Install the wire harness bracket to the intake manifold assembly with the bolt.
Connect the wire harness clamp to the engine hanger.
![]() |
Connect the purge line hose to the purge VSV.
Connect the purge VSV connector.
![]() |
Install the No. 1 ventilation hose with the 2 clamps.
![]() |
Connect the 2 water by-pass hoses to the throttle body assembly.
Connect the throttle body assembly connector.
| 3. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY |
![]() |
Connect the No. 1 fuel pipe sub-assembly.
| 4. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY |
![]() |
Connect the No. 2 fuel pipe sub-assembly (Click here).
| 5. INSTALL EFI FUEL PIPE CLAMP |
| 6. INSTALL NO. 2 WATER BY-PASS PIPE |
![]() |
Connect the 2 water hoses to the No. 2 water by-pass pipe.
Install the No. 2 water by-pass pipe with the 2 bolts.
![]() |
Connect the 2 water hoses to the No. 2 water by-pass pipe.
| 7. CONNECT VACUUM HOSE ASSEMBLY |
![]() |
Connect the vacuum hose assembly to the intake manifold assembly.
Install the vacuum hose assembly with the bolt.
| 8. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose assembly with the 2 clamps.
Connect the vacuum hose and No. 2 ventilation hose.
| 9. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Install the camshaft position sensor with the bolt and stud bolt.
| 10. INSTALL NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH |
![]() |
Pass the camshaft position sensor wire through the cover hole.
Install the cover with the 4 bolts.
Install the wire harness grommet to the belt cover.
Connect the sensor connector.
Install the sensor wire to the wire clamps on the cover.
Connect the engine wire to the 4 wire clamps on the cover.
| 11. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the inlet radiator hose.
| 12. INSTALL DRIVE BELT |
![]() |
Set the V belt onto every part except the No. 2 idler pulley, as shown in the illustration.
Loosen the V belt by turning the belt tensioner counterclockwise.
Set the V belt to the No. 2 idler pulley.
![]() |
After installing the belt, check that it fits properly in the ribbed grooves.
Check by hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.
![]() |
Check that the arrow on the belt tensioner is within area "A".
If it is outside area "A", replace the fan and generator V belt.
| 13. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
![]() |
If the coolant level is below the LOW line, repeat all of the procedures above.
| 14. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 15. INSPECT FOR FUEL LEAK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Techstream:
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
![]() |
Check that the pulsation damper screw rises up when the fuel pump operates.
If the operation is not as specified, check the following parts:
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.
| 16. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover onto the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 17. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY |
![]() |
Install the throttle body cover sub-assembly with the 2 nuts.
| 18. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY |
Install the front cowl top outer panel sub-assembly with the 7 bolts.

Install the wire harness clamp to the front cowl top outer panel sub-assembly.
Install the washer hose grommet to the front cowl top outer panel sub-assembly.
Connect the washer hose.
| 19. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the wiper motor and link assembly with the 4 bolts and nut.
Connect the connector.
| 20. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Engage the 6 claws and 8 guides and install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
| 21. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Engage the claw and install the front fender to cowl side seal.
| 22. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
| 23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, and then stop the wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the glass, as shown in the illustration.
Tighten the nut on the front wiper arm and blade.
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.
| 24. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, and then stop the wiper motor in the automatic stop position.
![]() |
Align the blade tip with the mark on the glass, as shown in the illustration.
Tighten the nut on the front wiper arm and blade.
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.