Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 2UZ-FE)

VANE PUMP (for 2UZ-FE) > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY


C181334
  1. Install the vane pump assembly with the 2 bolts and nut.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



2. CONNECT PRESSURE FEED TUBE


    C181317
  1. Install a new gasket to the pressure feed tube.

  1. Install the pressure feed tube with the union bolt .

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



3. CONNECT SOLENOID VALVE CONNECTOR


C181265
  1. Connect the solenoid valve connector.



4. CONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR


C181264
  1. Connect the oil pressure sensor connector.



5. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


C181263
  1. Connect the hose with the clip.



6. INSTALL FAN AND GENERATOR V BELT


    A053117E03
  1. Set the V belt onto every part except the No. 2 idler pulley, as shown in the illustration.

  1. Loosen the V belt by turning the belt tensioner counterclockwise.

  1. Set the V belt to the No. 2 idler pulley.



    A141644E02
  1. After installing the belt, check that it fits properly in the ribbed grooves.

  1. Check by hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.



    A141645E01
  1. Check that the arrow on the belt tensioner is within area "A".
    If it is outside area "A", replace the fan and generator V belt.

    HINT:
    When a new belt is installed, the arrow should be within area "B". If not, the fan and generator V belt is not installed correctly.



7. INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE


A185295
  1. Install the air cleaner assembly with air cleaner hose with the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }

  1. Tighten the air cleaner hose clamp.

  1. Connect the vacuum hose and No. 2 ventilation hose.

  1. Connect the air flow meter connector.

  1. Install the wire harness to the air cleaner cap.



8. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



9. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. for bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. for screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



10. ADD POWER STEERING FLUID


11. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)

    2. Repeat (*1) several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



12. INSPECT FOR POWER STEERING FLUID LEAK