Home › General › SPECIFICATIONS › 2UZ-FE ENGINE CONTROL

2UZ-FE ENGINE CONTROL > SERVICE DATA



MAF Meter:

Tester Connection
Condition
Specified Condition
4 (THA) - 2 (E2G)
-20°C (-4°F)
13.6 to 18.4 kΩ
20°C (68°F)
2.21 to 2.69 kΩ
60°C (140°F)
0.49 to 0.67 kΩ


Camshaft Timing Oil Control Valve:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω


VVT Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Cold
835 to 1400 Ω
Hot
1060 to 1645 Ω


Crankshaft Position Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω


Engine Coolant Temperature Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ


Throttle Body:

Tester Connection
Condition
Specified Condition
1 (M-) - 2 (M+)
20°C (68°F)
0.3 to 100 Ω


Knock Sensor:

Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ


Integration Relay (IG2):

Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
Battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
Battery voltage is applied to terminals 1B-6 and 1B-7
Below 1 Ω


Integration Relay (EFI):

Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1B-4
Battery voltage is not applied to terminals 1B-2 and 1B-3
10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3
Below 1 Ω


Fuel Pump Relay:

Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Integration Relay (A/F):

Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
Battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage is applied to terminals 1A-2 and 1A-3
Below 1 Ω


Circuit Opening Relay:

Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Air Fuel Ration Sensor (for Bank 1 Sensor 1):

Tester Connection
Condition
Specified Condition
1 (HT1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω


Air Fuel Ration Sensor (for Bank 2 Sensor 1):

Tester Connection
Condition
Specified Condition
1 (HT2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω


Heated Oxygen Sensor (for Bank 1 Sensor 2):

Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω


Heated Oxygen Sensor (for Bank 2 Sensor 2):

Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω


Accelerator Pedal Sensor:

Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 4.7 V


Power Steering Oil Pressure Sensor:

Condition
Specified Condition
Power steering not operating
0 to 2 MPa
Power steering operating
Values change from above value

Spark Plug 
Recommended spark plug
DENSO made: SK20R11
NGK made: IFR6A11
Correct electrode gap for new spark plug
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Maximum electrode gap for used spark plug
1.3 mm (0.0511 in.)
Standard insulation resistance
10 MΩ or more