Home › General › SPECIFICATIONS › 3UR-FBE ENGINE CONTROL

3UR-FBE ENGINE CONTROL > SERVICE DATA



MAF meter 
Tester Connection
Condition
Specified Condition
4 (THA) - 2 (E2)
-20°C (-4°F)
12.5 k to 16.9 kΩ
20°C (68°F)
2.19 k to 2.67 kΩ
60°C (140°F)
0.50 k to 0.68 kΩ

Camshaft timing oil control valve 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω

Engine coolant temperature sensor 
Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 k to 2.59 kΩ
Approx. 80°C (176°F)
0.310 k to 0.326 kΩ

Throttle body 
Tester Connection
Condition
Specified Condition
1 (M-) - 2 (M+)
20°C (68°F)
0.3 to 100 Ω

Accelerator pedal 
Tester display
Accelerator pedal released
Accelerator pedal depressed
Accelerator position No. 1
0.5 to 1.1 V
2.6 to 4.5 V
Accelerator position No. 2
1.2 to 2.0 V
3.4 to 4.7 V

Knock sensor 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ

Ignition relay No. 2 
Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
When battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
When battery voltage is applied to terminals 1B- 6 and 1B-7
Below 1 Ω

EFI relay 
Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1B-4
When battery voltage is not applied to terminals 1B-2 and 1B-3)
10 kΩ or higher
When battery voltage is applied to terminals 1B- 2 and 1B-3)
Below 1 Ω

Circuit opening relay 
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω

Fuel pump relay 
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω

Air fuel ration sensor (for Bank 1 sensor 1) 
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω

Air fuel ration sensor (for Bank 2 sensor 1) 
Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω

Heated oxygen sensor (for Bank 1 sensor 2) 
Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω

Heated oxygen sensor (for Bank 2 sensor 2) 
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω

A/F sensor heater relay 
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
When battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
When battery voltage is applied to terminals 1A- 2 and 1A-3
Below 1 Ω

Fuel pressure control valve relay 
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω

Spark Plug 
Recommended spark plug
DENSO made: SK20HR11
Correct electrode gap for new spark plug
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Maximum electrode gap for used spark plug
1.3 mm (0.0512 in.)
Standard insulation resistance
10 MΩ or more