Home › Engine / Hybrid System ยท 3UR-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A151828E01
  1. Install a new gasket and the water pump with the 8 bolts shown in the illustration.

    1. Bolt A

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

    1. Bolt B

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    1. Bolt C

    Torque:
    20 N*m{ 204 kgf*cm , 16 ft.*lbf }



2. INSTALL WATER PUMP PULLEY


    A151837E02
  1. Temporarily install the pulley with the 4 bolts.

  1. Using SST, hold the pulley and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



3. INSTALL INLET WATER HOUSING


    A162555E01
  1. Install a new gasket to the water pump.



    A183227E01
  1. Connect the No. 3 water by-pass hose to the inlet water housing.

  1. Install the inlet water housing with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



4. CONNECT NO. 5 WATER BY-PASS HOSE


A183225E01
  1. Connect the No. 5 water by-pass hose.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



5. INSTALL AIR PIPE SUB-ASSEMBLY


    A183221
  1. Install the air pipe with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the connector and install the wire harness with the 2 clamps.



6. CONNECT NO. 2 AIR INJECTION SYSTEM HOSE


A183220E01
  1. Connect the No. 2 air injection hose.

  1. Attach the wire harness clamp.

  1. Connect the air pump connector.



7. CONNECT NO. 3 AIR INJECTION SYSTEM HOSE


A183218E01
  1. Connect the No. 3 air injection hose.



8. CONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System)


    A165547
  1. Connect the 4 hoses.

  1. Install the water by-pass hose with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL NO. 1 WATER BY-PASS HOSE


    A158577E01
  1. Connect the No. 1 water by-pass hose to the water by-pass joint and water inlet housing.



10. INSTALL FAN SHROUD (w/ Trailer Towing System)


    A151842
  1. Install the fan pulley to the fan bracket.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A183238
  1. Attach the shroud claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the upper radiator tank.



    A187694
  1. Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.

    HINT:
    Align the hose clamp with the white paint mark on the hose, and install the hose clamp so that the hose clamp lock is between the fan shroud stoppers.

  1. Install the fan and generator V belt .

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



11. INSTALL FAN SHROUD (w/o Trailer Towing System)


    A151842
  1. Install the fan pulley to the fan bracket.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A183238
  1. Attach the shroud claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the upper radiator tank.

  1. Install the fan and generator V belt .

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



12. INSTALL INLET RADIATOR HOSE


    A198570E01
  1. Install the inlet radiator hose.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



13. CONNECT OUTLET RADIATOR HOSE


    A183234E01
  1. Connect the outlet radiator hose to the water inlet housing.



14. INSTALL AIR CLEANER HOSE ASSEMBLY


A198568E01
  1. Connect the air cleaner hose and tighten clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the No. 2 ventilation hose with the clamp.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the vacuum hose.



15. INSTALL AIR CLEANER ASSEMBLY


    A183246E01
  1. Attach grommet to air cleaner before mounting the air cleaner.

  1. Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.



    A183242
  1. Install the air cleaner with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector and install the clamp and wire harness.

  1. Connect the air cleaner hose and tighten the clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



16. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard Capacity 
    Item
    Specified Condition
    w/ Trailer Towing System
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)
    w/o Trailer Towing System
    13.6 liters (14.4 US qts., 12.0 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



17. INSPECT FOR COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



18. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



19. INSTALL V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.