Home › Engine / Hybrid System ยท 3UR-FE › LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL INLET WATER PIPE


    A162532
  1. Apply soapy water to 2 new O-rings and install them to the inlet pipe.

  1. Install the inlet pipe to the No. 1 heat exchanger cover.



2. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    A162531
  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket.



    A164415
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring.



  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.


    A178520E01

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


    1. A150825E02

      Apply seal packing as follows:
      Area
      Seal Packing Diameter
      Application Position from Inside Edge of Cover
      Continuous line area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      2.5 mm (0.0984 in.)
      Dashed line area
      6.4 mm (0.252 in.) or more, or within OK area shown in illustration
      7.0 mm (0.276 in.)
      Diagonal line area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      5.5 mm (0.217 in.)

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.



    A162541
  1. Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.



    A162542E01
  1. Temporarily install the timing chain cover with the 28 bolts and nut.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    25 mm (0.984 in.)
    8 mm (0.315 in.)
    Bolt B
    55 mm (2.17 in.)
    8 mm (0.315 in.)
    Bolt C
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt D
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt E
    55 mm (2.17 in.)
    10 mm (0.394 in.)
    Bolt F
    80 mm (3.15 in.)
    10 mm (0.394 in.)

    NOTICE:
    Make sure that there is no oil on the bolt threads.



    A174145E01
  1. Tighten the 3 bolts in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



    A163330E01
  1. Temporarily install the fluid coupling bracket with the 4 bolts.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt B
    80 mm (3.15 in.)
    10 mm (0.394 in.)



    A162527
  1. Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.



    A174146E01
  1. Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



    A162544E01
  1. Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


    NOTICE:
    A162545E01
    After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.



3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162524
  1. Install 5 new O-rings to the camshaft bearing caps (No. 2, No. 3).

  1. Install the gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.



    A162546E03
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A162523E01
  1. Install the cylinder head cover washer with a new seal and the 14 bolts.

    1. Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    1. Except bolt A

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A162526
  1. Install 5 new O-rings to the camshaft bearing caps. (No. 1, No. 3).

  1. Install the gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.



    A162547E03
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A162525E01
  1. Install the cylinder head cover washer with a new seal and the 14 bolts.

    1. Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    1. Except bolt A

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



5. INSTALL RADIO SETTING CONDENSER (for Bank 2)


    A163381
  1. Install the noise filter to the cylinder head cover with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A151832
  1. Connect the 8 ignition coil connectors.



7. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.



    A164230E01
  1. Using SST, install the pulley set bolt.

    SST
    09213-70011  
    09330-00021  

    Torque:
    300 N*m{ 3059 kgf*cm , 221 ft.*lbf }



8. CONNECT WIRE HARNESS CLAMP BRACKET


    A163733
  1. Connect the bracket to the timing chain cover with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



9. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Install the idler pulley with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



10. INSTALL WATER PUMP PULLEY


    A151837E02
  1. Temporarily install the pulley with the 4 bolts.

  1. Using SST, hold the pulley and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



11. INSTALL INLET WATER HOUSING


    A162555E01
  1. Install a new gasket to the water pump.



    A183227E01
  1. Connect the No. 3 water by-pass hose to the inlet water housing.

  1. Install the inlet water housing with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



12. INSTALL AIR PIPE SUB-ASSEMBLY


    A162553
  1. Connect the 2 hoses.

  1. Install the air tube with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



13. INSTALL NO. 1 ENGINE COVER


A158656

NOTICE:
Make sure that the No. 1 engine cover is level with the top surface of the intake port of the cylinder head for 1 and 2.

  1. Install the No. 1 engine cover.

    HINT:
    1. Align the No. 1 engine cover cutouts with the air tube.
    2. Align the No. 1 engine cover with the air switching valve surface and cylinder head wall.



14. INSTALL NO. 2 CYLINDER HEAD COVER


A158538

NOTICE:
Make sure that the No. 2 cylinder head cover is level with the top surface of the intake port of the cylinder head.

  1. Install the No. 2 cylinder head cover.

    HINT:
    1. Align the No. 2 cylinder head cover cutout with the air tube.
    2. Align the No. 2 cylinder head cover with the front water by-pass joint and cylinder head wall.



15. INSTALL FRONT WATER BY-PASS JOINT


    A162552
  1. Install 2 new gaskets and the water by-pass joint with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the No. 2 water by-pass hose to the water by-pass joint.



16. INSTALL NO. 1 WATER BY-PASS PIPE
  1. Install the No. 1 water by-pass pipe with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



17. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the 2 hoses.



    A162551
  1. Install the water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL AIR PIPE SUB-ASSEMBLY


    A183221
  1. Install the air pipe with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the connector and install the wire harness with the 2 clamps.



19. INSTALL NO. 1 WATER BY-PASS HOSE


    A162549
  1. Install the No. 1 water by-pass hose by connecting the hose to the water inlet housing and front water by-pass joint.



20. INSTALL GENERATOR ASSEMBLY
  1. Remove the generator assembly (Click here).



21. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.

  1. Disconnect the wire harness clamp.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



22. INSTALL ENGINE OIL COOLER (w/ Trailer Towing System)
  1. Install the engine oil cooler (Click here).



23. INSTALL OIL FILTER BRACKET (w/o Trailer Towing System)


    A163672
  1. Connect the ground wire to the cylinder block.

  1. Install the oil cooler bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



24. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (w/o Trailer Towing System)


    A118764E02
  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A162467
  1. Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.



    A163657
  1. Connect the sender gauge connector.



25. INSTALL OIL FILTER ELEMENT
  1. Install the oil filter element (Click here).



26. INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY


    A165142E01
  1. Connect the fuel tube with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



27. INSTALL COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



28. CONNECT NO. 2 AIR INJECTION SYSTEM HOSE


A183220E01
  1. Connect the No. 2 air injection hose.

  1. Attach the wire harness clamp.

  1. Connect the air pump connector.



29. CONNECT NO. 3 AIR INJECTION SYSTEM HOSE


A183218E01
  1. Connect the No. 3 air injection hose.



30. INSTALL INTAKE MANIFOLD
  1. Install the intake manifold (Click here).



31. INSTALL NO. 2 ENGINE WIRE


32. INSTALL ENGINE WIRE


33. CONNECT OUTLET HEATER WATER HOSE C


    A183229E01
  1. Connect the outlet heater water hose to the No. 1 water by-pass pipe.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



34. CONNECT INLET HEATER WATER HOSE C


    A183231E01
  1. Connect the inlet heater water hose to the water by-pass pipe.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



35. INSTALL AIR CLEANER HOSE ASSEMBLY


A198568E01
  1. Connect the air cleaner hose and tighten clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the No. 2 ventilation hose with the clamp.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the vacuum hose.



36. INSTALL AIR CLEANER ASSEMBLY


    A183246E01
  1. Attach grommet to air cleaner before mounting the air cleaner.

  1. Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.



    A183242
  1. Install the air cleaner with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector and install the clamp and wire harness.

  1. Connect the air cleaner hose and tighten the clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



37. INSTALL RADIATOR ASSEMBLY
  1. Install the radiator (Click here).



38. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20
    5W-20
    (0W-20 is best choice for fuel economy and good starting in cold weather.)

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts., 6.2 Imp. qts.)
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts., 5.8 Imp. qts.)
    Dry fill
    8.4 liters (8.9 US qts., 7.4 Imp. qts.)

  1. Install the oil filler cap.



39. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



40. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.